SxS 661
Refrigeration
User Guide
&
Installation & Service Instructions
U109200 - 07
1. Introduction
Thank you for buying this high quality appliance, we hope
that it provides you with a stylish, yet practical solution to
your cooling needs. We hope that this handbook supplies you
with all the information you require, but please contact us if
there is any thing you are unsure of using the Customer Care
Centre number on page 15.
DO NOT damage the refrigerant circuit. If it does
become damaged, do not use the appliance.
WARNING: Do not use mechanical devices (i.e. hair
dryers) to defrost this appliance.
•
When replacing old appliances, make sure that you
have disabled any locking mechanisms before disposal
– It may even be best to remove the appliance door
completely, to prevent children from becoming trapped
inside the appliance.
WARNING: This appliance must be earthed.
Always make sure a qualified person installs this
appliance.
The freezer compartment is rated at 4 stars.
•
•
The appliance must be connected to the power supply
safely. Loose connections, broken plugs and bare wires
are a safety hazard. Make sure that all connections are
sound.
Important!
Please be aware that this appliance is for domestic use only.
Before undertaking any routine maintenance or minor
repairs, disconnect the appliance from the electrical
supply. This includes cleaning, defrosting and changing
light bulbs.
The right-hand side of this appliance is a refrigerator, and
should be used for storing fresh foods.
The left-hand side of this appliance is used for freezing fresh
foods and storing frozen foods (convenience meals etc.)
•
•
•
Do not touch cold surfaces of the appliance while it is in
use as this will cause hands to stick to them leading to
freezer burns.
These instructions are intended for the user. They describe
the appliance and how to use it safely and correctly.
When moving the appliance take care not to damage
the leads, pipes or condenser unit. Should these parts
become damaged, contact a qualified service engineer.
Before you start
•
•
•
Before you plug the appliance into the mains, clean
the inside of the appliance using warm water and
bicarbonate of soda, then dry thoroughly.
Effervescent liquids (fizzy drinks) should never be
frozen. These liquids expand during freezing and
this may lead to the bottles/containers shattering or
exploding.
Please leave the appliance to stand for at least six hours.
This will allow the cooling system to settle following
transportation.
•
•
Foods that are intended to be defrosted or cooked first
e.g. breads, meats etc., must not be eaten in their frozen
state.
Check that no parts of the appliance are damaged,
especially parts of the cooling system, pipes or leads.
If damage has occurred, DO NOT install the appliance,
you should contact a qualified service engineer or
return the appliance to its place of purchase.
If food looks or smells strange, do not attempt to eat it.
If in doubt throw it away. Spoiled food can be harmful to
your health.
•
If the accessories inside the appliance have been
disturbed during transit, reposition them in accordance
with the instructions.
•
•
Never use electrical devices, such as hair dryers, to
defrost this appliance.
Never use sharp, metal implements to scrap ice off the
surface of this appliance. Only use implements, which
are fit for this purpose (i.e. plastic scrapers) and use
carefully to avoid damaging the lining of the appliance.
Make sure that the electrical supply to your plug socket is
correct for this appliance – The required information is on the
data badge of the appliance.
•
•
The cooling system contains refrigerant and oils, all of
which are harmful to health if leaked. Should leakage
occur, disconnect the appliance and ventilate the room
it is installed in. Take care to ensure that you do not get
any coolant near to, or in, your eyes.
Once the appliance is installed, cleaned and dry, it is ready to
be plugged in and switched on.
Safety
The data badge is located inside the appliance (refrigeration
compartment).
Contact a service engineer or arrange to have the
appliance removed. Do not use the appliance under any
circumstances.
WARNING: Use drinking water with this appliance.
WARNING: Keep this appliance clear of any
obstruction.
1
2. Positioning Your Appliance
If this appliance is situated in a cold environment (shed, out
house, garage etc.) it will affect its performance. You may find
that the performance of the appliance is not consistent and
this may damage foods. A consistent ambient temperature of
10°C or above is recommended.
Choosing the right location
This appliance should be installed in a room, which is dry and
well ventilated.
In order to ensure adequate ventilation, the appliance should
be at least 15 mm clear on all sides from kitchen cabinets,
and any units placed above the appliance must be clear by
15 mm – allowing adequate ventilation for the appliance. See
clearance diagram.
Connection to the electricity supply
Connect the appliance to the electrical supply (220 – 240V ~
50Hz) with the plug and lead, which are fitted. Connections
to the mains supply should be in accordance with local
regulations.
����
�����
�����
�����
This appliance will operate within a range of 187-
253V. Operation outside this range may result
in damage to the control panel, thermostat or
compressor, unless a regulator with a capacity of
750W, or higher, is installed.
The appliance must be plugged into an earthed
socket.
•
Always make sure that the plug is accessible after the
appliance has been positioned.
15mm
•
The refrigerator is supplied with a standard three-pin
plug, of which the one for grounding should never be
removed.
Care for the external cable
•
Hold the plug, not the electrical cable, when
unplugging the refrigerator.
•
Ensure that the refrigerator does not trap the electric
cable.
•
•
Do not step on the cable.
Avoid damage to the electric cable when moving the
refrigerator.
Damaged electrical cable
When the electrical cable is damaged or worn, turn off the
refrigerator and consult an authorized agent for replacement.
If inflammable gas leaks in the vicinity of the
refrigerator
•
Turn off any leaking valve.
If located close to a corner adequate spacing must be left for
door opening and removal of shelves. Refer to diagram.
•
Open the doors and windows.
DO NOT under any circumstances unplug electrical
appliances in the vicinity of the leak.
This appliance should be 10 cm at least from any electric or
gas cooker and 30 cm from any coal or oil stove. If this is not
possible, ensure that appropriate insulation is used.
Avoid exposing the appliance to direct sunlight, and sources
of heat (radiators, heaters, cookers, etc.).
2
Unplug the refrigerator when:
Door Handle Fitting
The door handles fix onto the mounting studs already fitted
to each door.
•
Cleaning or maintenance
•
Replacement of the lamp.
Use the M3 grub screws and Allen key from the instruction kit
bag. Each handle will require 3 grub screws.
Adjustable feet
Make sure that the appliance is on solid level flooring. If the
refrigerator is placed on a plinth, flat, strong and fire resistant
materials must be used.
1.
2.
Place the handle firmly over the mounting studs.
Insert the grub screw into the hole located under each
handle standoff bar.
This appliance has front adjustable feet, which can be used to
level the appliance, or adjust door alignment.
3.
Using the M3 Allen key, tighten the grub screw fixing
the handle to the door.
Do not over-tighten the grub screw.
Door adjustment
The doors may require some alignment adjustment before
you connect the appliance to the electricity supply. This can
be done by making minor adjustments to the feet:
If the freezer door height is lower than the refrigerator door,
use a screwdriver in the slots of the front left-hand adjustable
foot, turning clockwise until the freezer door height is raised
in line with the fridge door. If the freezer door is lower, adjust
the right-hand foot using the same method.
������
�����������
����������
3
3. About Your Appliance
Dairy Compartment
Ideal for storing foods such as eggs, cheeses, butter, cartons of
milk etc, separate from stronger smelling food.
Appliance Layout
Shelves
Number of shelves supplied; 4 in the fridge, 3 in the freezer.
Salad / vegetable drawer (Upper Crisper)
The upper drawer inside the refrigerator is used for storing fresh
fruit and vegetables that require careful cooling.
The shelves will not pull out accidentally when you remove
foodstuff from the appliance.
Foods that are likely to perish quickly should be placed
towards the rear of the appliance – where it is coolest.
Meat drawer (Lower Crisper)
The lowest drawer inside the refrigerator can be used to store
fresh meat in a way, which will avoid cross contamination with
other fresh foods.
Bottle holder
The bottle holder is intended for storing larger bottles (soft
drinks, water etc.) inside the fridge.
The lights
The interior lights come on when the door is opened. The
performance of the light is not affected by any of the appliances
other settings. Should the light fail to work, it is most likely that
the bulb needs replacing (see P16, Changing the Light bulb).
Like the shelves, the bottle holder will not pull out
accidentally and can be removed by holding the front edge
of the holder and tapping the underside upwards, until the
holder disengages from the 2 locations.
WARNING: Always make sure that large bottles do not
prevent the door from closing.
Freezer compartment
Refrigerator compartment
Fan
Ice Maker (inside ice bin)
Ice bin
Lamp
Lamp
Cantilever shelf
Cantilever shelf
Storage shelf
Storage shelf
Freezer draw
Crisper
4
4. Before Using Your Appliance
Environmental Notes
Using Your Appliance
Our products have been packaged using environmentally
friendly materials. All packaging can be recycled. Please
contact your local authority for details on recycling centres in
your area.
WARNING: Do not damage the refrigerant circuit
when installing or cleaning.
WARNING: Do not use any kind of mechanical device
in any compartments of this appliance unless they
All old electrical goods must be disposed of correctly. You
should never dispose of them with household waste. Local
councils / authorities can advise you as to what services they
provide for the disposal of old products – please be sure that
you contact them in order to dispose of all old appliances.
are of the type recommended by the manufacturer.
WARNING: Do not use any electrical devices to
defrost this appliance unless they are a type
recommended by the manufacturer.
Once the appliance has been installed and is connected
to the power supply the appliance will begin to work
automatically. You can adjust the settings of the appliance to
suit your requirements.
Many of the components in this appliance can be recycled.
Energy Saving Tips
Energy saving is especially important with cooling products.
Once the temperature required inside the appliance has been
reached, you should begin to load it with food. We would
recommend that you do this all in one go to prevent repeated
opening and closing of the door. See ‘Setting and Adjusting
the Temperature’for more information.
•
Check regularly that your appliance is well ventilated.
Poor air circulation around the appliance can lead to
inefficient operation.
•
Whenever possible adjust the thermostat to reflect
seasonal changes, and changes in the quantity of food
stored inside.
Note: The time required to reach the desired temperature will
vary, depending on the setting chosen, the amount of food
and the ambient temperature.
•
•
Freshly cooked foods, which are to be frozen, should be
cooled to at least room temperature before freezing.
Layers of ice and frost increase energy consumption
– make sure that your appliance is free of heavy frost
and ice.
Temperature selection
Higher settings on the thermostat (towards 5) mean lower
(colder) temperatures within the appliance (see the guide
below).
•
•
Should the door seal become dirty or damaged,
please clean or replace it. A poorly working door seal is
detrimental to the performance of the appliance.
Under certain conditions (Highest setting and low ambient
temperature), the temperature inside the refrigerator can
drop below 0°C.
The vents at the rear of the appliance should always
be clear/cleaned of dust and obstruction. Regularly
checking, and cleaning if need be, should help to keep
the appliance running effectively.
It is recommended that when the ambient temperature is
normal you set the thermostat to a medium setting.
Use the highest setting only when required or recommended.
Ensure that the appliance is installed in accordance with the
instructions given in this handbook – Failure to do so could
invalidate your warranty, resulting in service charges being
incurred, should you need an engineer.
Note: Temperatures within the appliance can be affected by
frequent opening of the door. Always try to keep the length
of time the door is open to a minimum.
Temperature Guide
Compartment DISPLAY
1
2
3
4
5
FREEZER
FRIDGE
Level
Level
-15°C -17°C -18°C -20°C -22°C
1
2
3
4
5
7°C
6°C
5°C
4°C
3°C
5
5. The Control Panel
�
�
�
�
�
�
�
�
�
�
�
A
B
C
D
E
Quick Freeze
G
H
I
Refrigerator temperature indicator
Crushed ice selected
Water selected
Freezer temperature
Refrigerator temperature
Ice/Water
J
Cubed ice selected
Freezer indicator
F
Freezer temperature indicator
Setting and Adjusting the Temperature
F G
‘Quick Freeze’
E
5
5
•
3
•
•
3
•
1
1
To use the ‘Quick Freeze’function, press button A. Indicator E
will illuminate to show you that the function is operational.
To switch ‘Super Freeze’off, press button A again – indicator E
will go out.
To adjust the refrigerator temperature, press button C. The
indicator (G) will illuminate. Each subsequent press of button
C will adjust the temperature scale by one. To clear the
setting, simply keep pressing button C until indicator (G) is
back to level 1.
Note: The quick freeze function will operate until the selected
temperature level (1 to 5) has been established.
To adjust the freezer temperature, press button B. The
indicator (F) will illuminate. Each subsequent press of button
B will adjust the temperature scale by one. To clear the
setting, simply keep pressing button B until indicator (F) is
back to level 1.
Open Door Warning
Should the door be left open for an extended period, an
alarm will sound to remind you to close the door.
6
Control Function Display
30 minutes after the final press of any button, the display will
go blank. The display will illuminate when the door is opened,
or if you press any button.
Switching the refrigerator On/Off
G
5
•
3
•
1
C
To switch off the refrigerator, press and hold button C for a
few seconds. The icon (G) will disappear.
To switch the refrigerator on again, press and hold button C.
Icon (G) will reappear and the appliance will begin to run as
usual.
Try not to open the door too often.
7
6. Storing and Freezing
Storing fresh foods
Freezing fresh foods
As with storing fresh foods, suitable packaging, correct
temperature and food hygiene will enhance the quality of the
food you are freezing.
Packaging fresh foods properly, using the correct
temperature and taking into account food hygiene will
enhance the quality of fresh foods stored within this
appliance.
Make sure that all foods for freezing are of a high quality, and
suitable for freezing.
Use plastic bags, aluminium foil or other food wraps to cover
fresh foods not in packaging to prevent flavour transfer and
prevent contamination.
Use suitable packaging (plastic bags etc.) to store food in, and
make sure that it is air tight or well sealed. Leaking packaging
will dehydrate the products and lead to loss of beneficial
vitamins.
Make sure that foods, which have been cooked and require
chilling, are at room temperature before placing them into
the appliance. Make sure that these foods are stored in
suitable containers.
Mark packages with the kind of food contained and the date
of storage.
Before storing items in multi packs (i.e. yoghurt) remove any
excess packaging.
Food needs to be frozen quickly, so it is best to freeze small
portions whenever possible and ensure that they are as cold
as possible before storage. The recommended maximum
weight for each portion is 2.5kg.
Make sure that foodstuffs are stored systematically (raw
meats with raw meats, dairy with dairy) to avoid flavour
transfer and cross contamination. Raw meats should be
stored towards the bottom of the appliance to prevent the
possibility of it dripping onto uncooked food. Other foods
should be stored above raw meat.
Keep food which is fresh away from food which is already
frozen, if you need to freeze fresh food every day, make sure
that it is in small portions to prevent this.
Do not exceed the maximum load for freezing – which is
given as 10kg / 24H - see data badge for details.
Never store anything, which is flammable, volatile or
explosive inside the appliance.
Beverages with high alcohol content should be stored
vertically in tightly sealed bottles.
Foods should not touch the rear wall of the appliance.
Delicate foods should be stored in the coolest part of the
appliance.
Try not to open the door too often.
Set the thermostat to make sure that foods remain suitably
cold, try to avoid freezing within the fridge. Using a
thermometer will help you to judge how cool the appliance
is. Place it into a glass of water and leave it inside the
appliance for several hours to get a reliable reading.
Some foods contain natural oils and acids (e.g. citric acid)
which can damage plastics if spilled – make sure these foods
are suitably contained.
Unpleasant odours inside the fridge are a sign that something
has spilled and cleaning is required. Using warm water with
bicarbonate of soda will clean the interior of the appliance
and remove most spillages. (See cleaning your appliance).
Always remember to remove perishable foods from this
appliance before taking prolonged trips of holidays.
8
Freezing procedure
This appliance is fitted with a ‘Quick Freeze’function. This
Storing frozen foods
When storing commercially frozen foods, please follow these
function is ideal if you are freezing large quantities of foods as guidelines.
it freezes quickly helping to preserve freshness and maintain
Always follow manufacturers’ guidelines for the
length of time you should store food for. Do not
exceed these guidelines!
the level of nutrients in foods which can be lost through
freezing.
•
•
•
Try to keep the length of time between purchase and
storage as short as possible to preserve food quality.
�
�
�
�
Buy frozen foods, which have been stored at a
temperature of –18°C or below.
�
Avoid buying food which has ice or frost on the
packaging – This indicates that the products might have
been partially defrosted and re-frozen at some point
– Temperature rises affect the quality of food.
•
•
When consuming ice cream or water ices allow them to
warm a little first to prevent freezer burns on hands or
tongue.
Should there be a power cut, or the freezer /
refrigeration appliance fail for any length of time you
may need to remove food from the freezer and store in
a cold, hygienic place (i.e. garage or outhouse area) until
the power is restored, or the appliance is repaired.
It is also advisable to use this function before you clean the
appliance interior to ensure that foods are as frozen as possible.
To prevent undue temperature rises; you should wrap the
foods in layers of insulating material, such as newspaper,
to help to maintain their temperature. It is also important
that any food affected by this situation should be either
consumed or cooked and re-frozen (where suitable) soon
afterwards in order to prevent health risks.
Layers of newspaper can also be used to help keep foods
cold while you are defrosting the freezer (see cleaning your
appliance).
9
7. Storage Areas
High humidity will keep foods such as grapes, cucumbers,
kiwi etc. fresh and crisp – this is achieved by opening fewer
holes in the moisture control.
About your Freezer Compartment
As with the refrigerator, certain areas of the freezer are better
for storage of certain foods.
Lower humidity is ideal for storing foods such as strawberries,
melons, tomatoes and beans. Opening more holes in the
moisture control will lower the humidity accordingly.
Ice creams and water ices are best stored towards the rear of
the appliance where it is coldest.
Large / heavier portions of food, such as meats joints for
roasting are best stored in the drawers at the bottom of the
appliance, while less weighty items should be stored on the
shelves – this is to prevent damage to the appliance.
Always make sure that the front edge of the crisper
compartment is underneath the crisper cover. When
removing the crisper, remove the compartment first before
the cover.
You should always make sure that food stored is suitable
for freezing, and that you have stored it securely inside the
appliance.
To remove the cover of the crisper (for cleaning etc.) remove
the drawer first. Lift the food shelf in an upward direction at
the rear (1) and pull it towards you (2). Then turn the shelf into
position (3). You must have the appliance door open by 90°.
Defrosting food for cooking
Should food become partially thawed, or defrosted it should
be consumed as soon as possible as the quality will be
affected by defrosting.
Always make sure that food is thoroughly defrosted
1
before cooking and no ice crystals remain. This
is especially important for poultry, as this can be
extremely harmful to health.
Always follow the defrosting instructions on packaging
when defrosting ready meals – manufacturers’
guidelines are always best, as some frozen foods should
be cooked from frozen.
4
2
About your Refrigeration Compartment
Temperature differences exist inside the refrigerator so it
is sensible to store different foods in different areas of the
appliance.
4
4
1.
Eggs, butter and cheeses. (Dairy compartment with
cover)
3
2.
3.
4.
Smaller bottles, cans, jars, packages.
Large bottles, soft drinks, water, wine etc.
4
Any fresh produce – store carefully to avoid cross
contamination.
5.
6.
Salad / vegetable drawer
Fresh, uncooked meats – store carefully to avoid cross
contamination and spillages.
5
3
Crisper compartment
To keep fruit and vegetables crisp and fresh, this appliance
has a crisper compartment with adjustable humidity.
6
3
10
8. Using the Icemaker & Water Dispenser
prolonged break. Discard these cubes.
Before using the Icemaker/Water
Dispenser
To ensure that the ice cube tray is filled to maximum capacity,
you will need to manually arrange the ice cubes periodically.
Water supply installation
Pressure of the cold water supplied to the automatic icemaker is
between 1.5 - 8.5 bar.
Some ice cubes may stick together when dropped into the
storage box – you will need to separate these to ensure
maximum use of the icebox.
Installation instructions for the connection kit (to a
drinking water supply) are found inside the fridge.
First use of the icemaker / water dispenser
Do not consume the first seven (approx) glasses
of water, as there may be dust and / or impurities
within the water pipes.
Caution: Only an authorised person should install
the water pipes and filter.
•
The water tube should be of an appropriate length
- usually 12 metres - and should be free of bends
after being inserted into place. If the tube is too long
then pressure will be reduced, therefore reducing the
capacity of ice making.
This will ensure that the pipes are cleared. If in doubt, keep
re-using the dispenser until the water runs clear.
Noises during ice making
The ice making process can be noisy. You may hear ice being
dropped into the storage compartment. This is perfectly
normal.
•
•
•
Always use potable / drinking water.
Keep the water tube clear of heat sources.
The water tube should be installed and tested by
authorised personnel.
Storing ice for extended periods
Ice, which is stored for a long period of time, may go an
opaque colour and have a strange odour. We recommend
that you dispose of this ice, remove and clean the icebox.
Allow the tray to dry thoroughly and cool down before
replacing into the appliance to prevent ice from sticking.
•
When used for the first time, press and hold the cold-
water button for one minute to prime the water supply.
Do not press the cold-water button for any longer as
this may cause the valve to heat up.
Precautions
Preventing ice from being made
•
•
•
Never expose the water pipe to temperatures below 0°C
to avoid freezing.
If you do not require any ice over a prolonged period of time
(i.e. during winter) you can switch off the valve between the
water supply and the appliance. It is recommended that you
clean the icebox, dry it carefully and replace it back into the
appliance – this will prevent any odours being produced.
Test the tubing for leaks by flushing the tube through
with water, until the water runs clear.
After the appliance has been sited into the location of
your choice, make sure that the water tube is arranged
so it does not incur damage through bends and kinks
and is clear of any heat sources.
Installing and removing the ice cube storage
tray
To remove the icebox, press the top of the drawer and
simultaneously pull the bottom, releasing the unit.
•
•
•
A qualified appliance installer must install this
appliance.
Once the temperature inside the freezer is at -15°C ice
production will begin.
Do not over use the icemaker. If you attempt to use the
ice cube button too often it will go into a shut down
mode. This is perfectly normal and requires you to wait
for one hour before attempting to re-use it.
•
•
Do not use delicate or fragile glassware.
Do not touch the ice cube outlet with your hands, or
any implements to avoid injury or damage.
How the icemaker works
In every cycle 8 ice cubes are produced.
Capacity of the icemaker depends on the freezer
temperature, the ambient temperature of the environment
around the appliance and how often the freezer door is
opened.
Do not store ice cubes, which are produced during the
first batch of cubes following appliance start up, or after a
11
If the icebox cannot be easily fitted, remove it and turn the
corkscrew mechanism 90°. Then reinstall the icebox, ensuring
that the catch pin on the tray fits into the slot on the shelf.
Ice cubes
�
�
�
�
�
If the ice maker does not work properly
1.
2.
3.
Hold the glass to the dispenser.
Press the button for ice cubes.
The volume of the icebox equals the quantity of ice cubes,
which the appliance can make in one day. Occasionally small
number of ice cubes may remain inside the box. If the ice
gets stuck, this will result in abnormal operation of the ice
cube maker. To avoid this problem, remove the icebox and
rearrange the ice cubes, and remove ice cubes, which cannot
be separated.
Slightly push the glass onto the lever switch and the ice
cubes will be dispensed into the glass.
Cool water supply
Always keep the ice cube outlet clean and clear of
obstructions.
�
�
�
�
�
Operating the Icemaker & water
dispenser
There are three options available with this accessory
– crushed ice, cool water or ice cubes. Always make sure that
you hold your glass up to the dispenser before making your
selection to avoid spillages.
Crushed ice supply
1.
2.
3.
Hold the glass to the dispenser.
Press the button for crushed ice.
Slightly push the glass onto the lever switch and the
crushed ice will be dispensed into the glass.
1.
2.
3.
Hold the glass to the dispenser.
Press the button for cool water.
Slightly push the glass onto the lever switch and the
cool water will be supplied.
�
�
�
�
Notes
�
When crushed ice is supplied;
Some times you may receive crushed ice when you
have selected ice cubes as there may be crushed ice
remaining in the crushing mechanism. This is normal.
Try again until you receive ice cubes.
If crushed ice is supplied frequently, you may notice a
build up of ice around the front of the icebox. This will
defrost automatically and is not a problem.
When cool water is supplied;
Following installation, cool water may not be available
immediately. This is due to air in the pipes. Press the
cool water supply button until water is dispensed to
clear the air. This can take up to two minutes.
12
The water supply will become cooler and cooler
gradually.
In the event of a power cut
Should there be a prolonged power cut you may need to
remove food from the freezer compartment and store it in
a cold place, wrapped in layers of newspaper to preserve
suitable temperatures.
Cool water does not contain ice – this should be added
before the water.
Safety
In the event of a power cut, food should remain safely
cold for 3 hours approx.
Do not use excessively deep, narrow, fragile or
delicate glasses.
Once power is restored – replace the food back into the
freezer compartment.
•
Hold the glass as close as possible to dispenser to avoid
spilling water, dropping ice or blockages in the ice cube
dispenser.
Should food begin to defrost, or the power cut last longer
than expected, it is advised that you consume any food
removed from the freezer.
•
Five seconds after the final delivery of ice or water,
the dispenser flap will close with a ‘phutt’sound. Hold
the glass still for a further 2 – 3 seconds (for ice), 1 - 2
seconds (for water) after you have filled your glass and
released the lever switch as additional water or ice may
be produced.
If the power outage is short term, most foods can be left
inside the freezer compartment – this is the best way of
preserving temperature – and surrounded by ice cubes from
the icebox. This is also an ideal solution for power outages
you may have been pre warned about.
•
•
Regularly clean the dispenser.
When experiencing a power cut of any kind, do not add any
extra foods to the freezer.
Crushed ice may be dispensed instead of cubed ice if
crushed ice was the last option selected.
Never place canned drinks or foods inside the
dispenser, as this will damage the crushing
mechanism.
Do not touch the dispenser, or remove the icemaker
cover to prevent accidental injury or damage to the
appliance.
•
First supply of water (seven glass approx) and ice cubes
(20 pieces approx) should not be consumed after initial
start up or following a lengthy break in use. Dispose of
these accordingly.
•
•
Do not place ice cubes, which have not been produced
by the icemaker into the storage drawer to prevent
damage to the mechanism.
Insufficient water supply may lead to small ice cubes.
Excessive water supply may lead to larger cubes, which
may stick together, cause leaks and block the dispenser.
You should adjust the tap or contact a service engineer.
Automatic defrosting
There is no need to defrost the refrigerator as this appliance
has automatic defrost.
Do not use mechanical devices to accelerate the
defrosting process – unless they are of a type
recommended by the manufacturer.
13
9. Maintenance and Cleaning
Cleaning the inside of your appliance
Checking the water quality
Periodically, the water dispenser display will change colour
from blue to red as a warning to check the water quality.
•
Always disconnect the electricity supply before you
start cleaning.
•
•
Empty the appliance of food and remove the shelves.
To maintain water quality, the filter will need replacing from
time to time. We recommend that the water filter is replaced
every 2 years. However, if the water quality show signs of
deterioration, either visually or in taste, then the filter should
be changed sooner.
The interior can be cleaned using warm water and
bicarbonate of soda, with a soft cloth. Make sure that
the interior is then dried carefully with a suitable cloth.
Do not use harsh abrasives, or aggressive cleaners as
these can damage the interior of the appliance.
•
Shelves and other accessories (plastic and glass parts)
can be cleaned in the sink using liquid dish washing
liquid and warm water. Make sure all soap is rinsed off
and all parts are dry before replacing them inside the
appliance.
�
�
�
�
�
•
Always keep the door seals clean.
Removing the shelves/Salad/vegetable
crisper cover
•
Lift the food shelf in an upward direction at the rear
(1) and pull it towards you (2). Then turn the shelf into
position (3). You must have the appliance door open by
at least 90°.
To reset the display, press and hold drinks dispenser button
for 5 seconds. The warning will deactivate and the display
light will return to blue.
When not in use
If you are not using the appliance for an extended length
of time, it is recommended that you switch of the electrical
supply, empty any food out, clean the inside of the appliance
and leave the door ajar. This will save energy, and also prevent
a build up of stale odours inside.
•
To remove the crisper cover, remove the crisper drawer
first and then follow the above directions.
Do not wash plastic parts in a dishwasher.
Clean the exterior of the appliance with a soft cloth and an
alcohol based cleaner. Do not use abrasive cleaners on the
exterior of the appliance.
The vents at the rear of the appliance should be cleaned
periodically using a soft bristled brush or the brush
attachment of a vacuum cleaner.
Once cleaning is completed, reconnect the electricity supply
and replace the food.
14
Changing the plug (UK)
Changing the light bulb
This appliance comes fitted with a 13amp plug fitted. Should
you need to replace the fuse, a 13amp ASTA approved
(BS 1362) must be used. Should the plug itself need to
be replaced, the wires in the mains lead are coloured in
accordance with the following code:
Before replacing the light bulb, switch off the electricity
supply to the appliance and unplug the appliance.
Lamp required: 220 – 240V~25W (fridge only)
Lamp required: 220 – 240V~40W (freezer only)
Lamp holder: E27 (Do not exceed the wattage given
for lamps)
Green and yellow = Earth
Blue = Neutral
To replace the lamp;
Brown = Live
1.
2.
3.
4.
Pull the lampshade towards you.
Hold up (1) and pull out (2) the lampshade.
Rotate the lamp anticlockwise until the lamp is released.
Always replace the bulb with one that is identical.
Earth - Yellow/Green
Bulbs are not covered by any warranty, but can be purchased
at your local hardware store. Remember to take the old bulb
with you if you are unsure of what kind of bulb to buy.
Live - Brown
Neutral - Blue
MAX
25W
Wiring of a standard 13 amp British three- pin plug
The wire coloured green and yellow must be connected to
terminal marked with the letter E, coloured green and yellow
or marked with the earth symbol:
The wire coloured blue must be connected to the terminal
marked with the letter N, or coloured blue.
The wire coloured brown must be connected to the terminal
marked with the letter L or coloured brown.
Upon completion, there must be no cut or stray wire present
and the cord clamp must be secure over the outer sheath.
15
10. Troubleshooting
The appliance fails to work when first connected to the
electricity supply
The appliance is making noises
The appliance is cooled by the compressor, which will
make a certain amount of noise when the appliance is
switched on. The amount of noise depends on the age
of the appliance (older appliances may become noisier),
the positioning of the appliance (a levelled appliance is
less noisy) and how the appliance is used.
Check there are no faults with the socket you are using
by plugging in an appliance you know to be working.
Make sure that you have switched the appliance ‘on’.
The voltage may be incorrect.
During use, you may hear the sound of the refrigerant
being circulated, and the sound of it flowing when
the compressor is off. The sound of the compressor
itself, which is a humming sound and a click when the
compressor switches off and on.
The appliance seems to be continually running
The appliance will make a sound when first started; this
will gradually fade over a period of time.
The door has been opened frequently.
The door isn’t properly closed because the seals need
cleaning, or are damaged.
When you are starting the appliance for the first time,
or have had the appliance switched off for a prolonged
length of time, the sounds described above may be
louder.
The door is damaged – leading to it dropping out of
correct alignment with the appliance.
You may hear hissing or gurgling noises from the
appliance – these are due to the automatic defrosting
process.
The appliance has recently been filled with more food
than usual.
Ventilation is compromised – the vent requires cleaning
or clearing from obstruction.
Piping and the evaporator may also make noises should
the ambient temperature around the appliance change.
There is inadequate ventilation around the appliance
– other appliances or units are too close. The appliance
has been overloaded with food for chilling or freezing.
If noises seem to be too loud, or a little unusual it
is more than likely because the appliance requires
levelling, or it is touching a unit.
The ‘Quick Freeze’function has been switched on.
Flashing indicator bar
The outer casing of the appliance is warm
In the unlikely event of a flashing indicator bar occuring,
please contact your service provider.
The appliance may become warm on the outside when
first switched on to prevent condensation forming.
The lamp does not work
The appliance is not plugged into the wall socket / a
fuse has blown.
The bulb requires replacing.
The temperature inside the appliance is not right
The door has not been closed properly.
The appliance is too close to a heat source, or in direct
sunlight.
The vents at the rear are blocked / obstructed.
16
11. Warranty/After Sales Service
If consultation or technical assistance is needed, please
provide the local authorised service agent with the purchase
invoice and the product code/serial number, which is located
inside the refrigerator – Top left-hand side.
The 2 year free maintenance for the operation of the
appliance started from the date of purchase of this product.
Any cosmetic damage to the appliance must be reported
within 90 days of delivery.
For in-warranty service please call 0845 6035312.
For general enquiries please call 0870 7895107.
17
Clarence Street, Royal Leamington Spa,
Warwickshire, CV31 2AD, England.
Tel: +44 (0) 1926 457000 Fax: +44 (0) 1926 450526
E-mail: [email protected]
|