Tuning guide/ reference pitch LED display
CHROMATIC TUNER STX1
INSTRUCTION MANUAL
In the auto and manual modes, the difference in pitch between the note
indicated on the display and the note given by the instrument is indicated by
the LED that lights up. (See the numeral on the right of the LED that lights up.)
The LED display also indicates the reference pitch you have set. (See the
numeral on the left of the LED that lights up.)
NAME AND OPERATION OF PARTS
Before use, pull out the insulating sheet from
Built-in microphone
the battery compartment, as shown in the
illustration below. If the sheet is torn off and left
inside the compartment, open the battery hatch
by referring to “BATTERY CHANGE” below,
and remove the remainder of the sheet
completely. Otherwise, the tuner will not be
turned on.
Use it to input a note directly from the instrument in the “MIC” input method.
When the “CLIP” input method is selected, the built-in microphone is disabled.
Vibration sensor/built-in speaker
In the “CLIP” input method, it senses the vibration generated by the instrument.
When the “MIC” input method is selected, the vibration sensor/built-in speaker
is disabled. In sound mode, the reference note you have set is produced from
the built-in speaker.
Note: The battery included with the tuner is a monitor
battery, and the battery life may be shorter than
the specified period.
Clip
Attach the tuner to the instrument using it to sense the vibration it generates.
HOW TO TUNE THE INSTRUMENT
● Auto/manual mode
Play a note with the instrument, and tune it according to the note indication
and the tuning guide
1. Press the power button
When the “CLIP” input method is selected, attach the tuner to the instrument
using the clip
2. Select the tuning mode. Press the mode button
to the auto ( ) or manual ( ).
.
- - - - -
to select the “CLIP” or “MIC” input method.
.
to set the tuning mode
3. When the manual mode is selected, press the note button
you wish to tune.
to set the note
4. To change the reference pitch, press the pitch button
to set the desired pitch.
5. Play the instrument to give a note. When the “MIC” input method is
Power button
selected, bring the instrument close to the built-in microphone
6. Tune the instrument until the LED at the center of the tuning guide
.
With each press, the tuner stands by for “CLIP” and “MIC” input, and is turned
off in order.
lights
up in green. In the auto mode, also check the input note with the note
indication
● CLIP input method:
The vibration sensor
.
senses the vibrations generated when the instrument
gives out a note, and tuning is made using them. This input method is
convenient for the tuning in noisy environments or in a situation where
other instruments are played nearby.
● MIC input method:
Tuning is made using the note of the instrument input through the built-in
microphone
.
Mode button
[Flat]
● Sound mode
The tuner gives out the note you wish to tune, and tune the instrument on the
basis of the reference note the tuner produces.
[In tune]
[Sharp]
Use the button to select the tuning mode from auto (
sound ( ).
), manual (
) and
Auto mode
:
By playing a note, the tuner automatically identifies and
indicates the note having the pitch closest to it. It also
indicates that the pitch of the input note is lower or higher
than that of the indicated note.
1. Press the power button
to select the “CLIP” or “MIC” input method.
(The sound mode is available irrespective of the input method selected.)
2. Select the tuning mode.
Manual mode
Sound mode
:
:
Set the note you wish to tune, and then, play a note. The
tuner indicates that the pitch of the input note is lower or
higher than that of the note you have set.
Press the mode button
3. Press the note button
to set the tuning mode to the sound (
to set the note you wish to tune.
).
The tuner gives out the note you have set. Tune the
instrument on the basis of the reference note the tuner
produces.
4. To change the reference pitch, press the pitch button
to set the desired pitch.
5. Tune the instrument on the basis of the reference note the tuner produces.
● Precautions on tuning
Pitch button
1. The tuner may pick up noise from the surrounding environment or the
hum noise generated by electric appliances, and shows indications as if
a note is played. This is not a malfunction, and the tuner operates
properly when a note is played.
2. When the “MIC” input method is used, it is recommended that the tuning
procedure be performed in a quiet environment for accurate tuning.
Also, bring the instrument close to the tuner to register a note.
3. If you find it difficult to tune the instrument with the “CLIP” input method,
re-attach the tuner in such a position to the instrument that the vibrations
are transmitted to the tuner more clearly.
Use the button to set the reference pitch (frequency of A4).
By pressing the button, an LED of reference pitch LED display
a certain period of time to show the current pitch setting. With each press of
the button while the LED is flashing, the reference pitch increases by 1 Hz. It
increases continuously if the button is kept pressed.
flashes for
* If the tuner is left untouched with an LED flashing, the reference pitch indicated by the LED
is automatically registered in a certain period of time.
● Settable range:
415 Hz ⇒ 438 Hz ⇒ 439 Hz ⇒ • • • • • ⇒ 444 Hz ⇒ 445 Hz
AUTO POWER-OFF FUNCTION
(at 1 Hz steps from 438 to 445 Hz)
The tuner is equipped with an auto power-off function as described below to save
the battery energy.
Note button
Use the button to set the note you wish to tune.
With each press, the note changes over at one-semitone step. It changes
continuously by keeping the button pressed.
* In the auto mode, the note button is disabled as the tuner automatically identifies and
indicates the input note.
● Auto/manual mode
1. If none of the buttons
built-in microphone
,
and
is pressed, if no note is input in the
senses no vibrations
or if the vibration sensor
for approximately 10 seconds while the power is turned on, the liquid
crystal display becomes slightly dim. (Power save mode, Phase 1)
● Settable range:
2. If the tuner is left untouched further for approximately five more minutes
without sensing a note or vibrations, the liquid crystal display becomes
Manual mode
Sound mode
:
:
C ~ B (12 notes)
C4 ~ B4 (12 notes)
black, and the green LED at the center of the tuning guide
flashing. (Power save mode, Phase 2)
starts
Liquid crystal display
Note indication
Auto mode
3. If the tuner is left untouched further for approximately 15 more minutes
without sensing a note or vibrations, the tuner is turned off automatically.
(Auto power-off function)
: By playing a note, the tuner automatically identifies
and indicates the note having the pitch closest to
it. (The difference in octave is not indicated.)
Manual/sound mode: The note you have set is indicated. (The octave
cannot be set.)
Input method indication
● Sound mode
1. If none of the buttons
,
and
is pressed for approximately 10
The input method you have selected is indicated.
seconds while the power is turned on, the liquid crystal display becomes
slightly dim.
Mode indication
2. If the tuner is left untouched for approximately 5 more minutes, the tuner
is turned off automatically. (Auto power-off function)
: Auto mode
: Manual mode
: Sound mode
|