OWNER'S
MANUAL
ECD-T1535
PLL Synthesized Stereo Radio with
Digital Compact Disc Player
• 1 pair of RCA output
• CD-R/CD-RW Compatibility
• 4 preset Equalization
• Auxiliary Input
1. Dashboard
2. Nut (5mm)
1
6
3. Spring washer
4. Screw (5 x 14mm)
5. Screw
4
5
2
3
6. Strap
Be sure to use the strap to secure the
back of the unit in place. The strap can
be bent by hand to the desired angle.
(Fig. 2)
Removing the unit
1. Frame
1
2. Insert fingers into the groove in the front
of frame and pull out to remove the
frame. (When reattaching the frame,
point the side with a groove downwards
and attach it.)
2
3
3. Lever
Insert the levers supplied with the unit
into the grooves at both sides of the unit
as shown in figure until they click.
Pulling the levers makes it possible to
remove the unit from the dashboard.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on the sides of the unit.
Fastening the unit to the factory radio
1
mounting bracket.
1. Select a position where the screw holes
of the bracket and the screw holes of
the main unit become aligned (are fitted),
and tighten the screws at 2 places on
each side.
2
4
Use either truss screws (5 x 5mm) or
flush surface screws (4 x 5mm),
depending on the shape of the screw
holes in the bracket.
5
3
2. Screw
2
3. Factory radio mounting bracket
4. Dashboard or Console
5. Hook (Remove this part)
5
Note: The mounting box, outer trim ring,
and half-sleeve are not used for method B
installation.
3
HOW TO REMOVE AND INSTALL THE FRONT PANEL
(OPTIONAL)
1. Press the release button and pull-off the front panel.
Store front panel in the case.
2. To install the front panel, insert the panel into the housing and make sure the panel
is properly installed, otherwise, abnormalities may occur on the display or some
keys may not function properly.
REMOVING THE FRONT PANEL
Front Panel
Release Button
INSTALLING THE FRONT PANEL
4
WIRING CONNECTION
MAIN UNIT
ANTENNA CONNECTOR
IGNITION RED
SWITCH (B+)
YELLOW
MEMORY
BACK-UP
(GREY)
Rch RED
RCA CABLE
BLACK
GROUND (B–)
Lch WHITE
BLUE
POWER
ANTENNA
GREY
WHITE
FRONT Lch
SPEAKER
FRONT Rch
SPEAKER
GREY/BLACK
WHITE/BLACK
GREEN
VIOLET
REAR Lch
SPEAKER
REAR Rch
SPEAKER
GREEN/BLACK
VIOLET/BLACK
5
OPERATION
11
7
1 2
3
5
8
18 19 13
4
9
12
10
24
20
21
22 14 23
6 16 15 17
26 25
GENERAL OPERATION
• ON/OFF
Switch on the unit by pressing any button [except button (7) and eject button
(4)]. When system is on, press PWR button (9) to turn off the unit.
• FACEPLATE RELEASE
Press button (7) to detach the removable faceplate.
6
The adjustment mode will change in the following order:
Volume
Bass
Treble
Balance
Fader
By pressing VOL button + (11) or VOL button – (12), it is possible to adjust the
desired sound level.
• LOUDNESS
Press BND/LOU button (13) for several seconds to reinforce the bass output and
display will show “LOUD”. Press it for several seconds again to release this function.
• SET THE CLOCK
Press the DSP button (15), the clock is shown on the LCD display. Then hold down
the button until the clock flashes. Then press the MANU/SKIP
button (17) to
change hours or MANU/SKIP button
(16) to change minutes.
• SELECT MODE
Press MOD button (6) shortly to choose desired listening mode.
[e.g. radio mode to CD mode to AUX mode]
• MUTE
Press MUT button (3) to mute the sound instantly. If any button is pressed in the
mute state, the mute mode is released.
• LIQUID CRYSTAL DISPLAY
Exhibit current frequency and activated functions on the display (8).
• EQUALIZATION
Press EQ button (19) to turn on equalization function and to select desired audio
mode. There are five kinds of mode as below:
FLAT
CLASSICS
POP M
ROCK M
DSP OFF
• AUXILIARY INPUT
The unit can be connected to a portable audio player through the AUX IN jack (24).
To hear the input signal, press MOD (6) button several times until the display shows
“AUX”.
• FLASHING LED
If the front panel is not installed in the main unit, the LED (25) will be flashing.
• RESET
RESET button (26) can be activated with either a ball point pen or thin metal
object. RESET button (26) is to be activated for the following reasons:
- Initial installation of the unit when all wiring is completed.
- All the function buttons do not operate.
- Error symbol on the display.
7
RADIO OPERATION
• BAND SELECTION
At tuner mode, press BND/LOU button (13) to select the desired band.
The reception band will change in the following order:
FM1
FM2
FM3
AM
• STATION SELECTION
Press MANU/SKIP
button (16) or MANU/SKIP
button (17) to activate
automatic seek function. To select manual tuning mode, press for several seconds
until “MANUAL” appears on the display. If both buttons are not pressed for several
seconds, the tuner will return to seek tuning mode and “AUTO” will appear on the
display.
• LOCAL/DISTANCE
Press LOC button (2) to select between local and distant stations.
Local setting for reception of strong station, and a distant setting for reception of
weaker stations. This function is in effect during AUTO SEEK operation.
• AUTOMATIC MEMORY STORING & PROGRAM SCANNING
- Automatic Memory Storing
Press ATP button (18) for several seconds, the radio will search from the current
station and check the signal strength until one cycle search is finished. The 6
strongest stations detected will be stored into the corresponding preset button.
- Program Scanning
Press ATP button (18) shortly to scan preset station.
• STATION STORING
Press any one of the preset buttons (14) (M1 to M6) to select a station which had
been stored in the memory. Press this button for several seconds to store the
current station into that preset button.
• SEEK FUNCTION
Press SEEK button (1) to scan and hear all tunable stations for a few seconds.
Press SEEK again to stop at current station.
8
CD OPERATION
• SELECT TRACKS
Press MANU/SKIP
button (16) or MANU/SKIP
button (17) to move to the
previous track or the following track. Track number shows on display.
Hold MANU/SKIP
button (16) or MANU/SKIP
button (17) to fast reverse or
fast forward. CD play starts from when you release the button.
• PAUSE PLAYING
Press PAU button (20) to pause CD player. Press it again to resume play.
• REPEAT THE SAME TRACK
Press RPT button (22) to continuously repeat the same track. Press again to stop
repeat.
• PREVIEW ALL TRACKS
Press SCN button (21) to play first several seconds of each track on the current
disc. Press again to stop intro and listen to track.
• PLAY ALL TRACKS IN RANDOM
Press SHF button (23) to play all tracks on CD in random order. Press again to
cancel the function.
• EJECT
Press (eject) button (4) to stop CD playing and eject the disc from the disc slot (5).
9
Note:
A. Notes on discs:
1. Attempting to use non-standard shape discs (e.g. square, start, heart) may
damage the unit. Be sure to use round shape CD discs only for this unit.
2. Do not stick paper or tape etc., onto the label side or the recording side of
any discs, as it may cause a malfunction.
3. Dirt, dust, scratches and warping discs will cause misoperation.
B. Notes on CD-Rs (recordable CDs)/CD-RWs (rewritable CDs):
1. Be sure to use discs with following marks only for the unit to play:
Recordable
Rewritable
2. The unit can only play a CD-R and CD-RW that is finalized. (Please refer to the
manual of your CD-R/CD-RW recorder or CD-R/CD-RW software for more
information on finalization process).
3. Depending on the recording status, conditions of the disc and the equipment
used for the recording, some CD-Rs/CD-RWs may not play on this unit. (See *1)
*1: To have more reliable play back, please see following recommendations:
- Use CD-RWs with speed 1x to 4x and write with speed 1x to 2x.
- Use CD-Rs with speed 1x to 8x and write with speed 1x to 2x.
- Do not play a CD-RW which has been written for more than 5 times.
10
SPECIFICATION
GENERAL
Power Supply Requirements
Chassis Dimensions
Tone Controls
: DC 12 Volts, Negative Ground
: 178 (W) x 165 (D) x 50 (H)
- Bass (at 100 Hz)
- Treble (at 10 KHz)
Maximum Output Power
Current Drain
: + 10 dB / – 10 dB
: + 10 dB / – 10 dB
: 40W x 4 (ch)
: 15 Ampere (max.)
CD PLAYER
Signal to Noise Ratio
Channel Separation
Frequency Response
: More than 55 dB
: More than 50 dB
: 40 Hz - 18 KHz
RADIO
FM
Frequency Coverage
IF
Sensitivity (S/N = 30 dB)
Stereo Separation
: 87.5 to 107.9 MHz
: 10.7 MHz
: 4 µV
: > 25 dB
AM
Frequency Coverage
IF
Sensitivity (S/N = 20 dB)
: 530 to 1710 KHz
: 450 KHz
: 36 dBu
11
TROUBLE SHOOTING
Before going through the check list, check wiring connection. If any of the problems
persist after check list has been made, consult your nearest service dealer.
Symptom
No power.
Cause
Solution
The car ignition switch is
not on.
If the power supply is properly
connected to the car accessory
circuits, but the engine is not
running, switch the ignition key
to “ACC”.
The fuse is blown.
Replace the fuse.
Disc cannot be
loaded or ejected. the player.
Presence of CD disc inside Remove the disc in the player,
then put a new one.
Disc is upside-down.
Insert the compact disc with
the label facing upward.
Compact disc is extremely Clean the disc or try to play a
dirty or defective disc. new one.
Temperature inside the car Cool off or until the ambient
is too high.
temperature returns to normal.
Condensation.
Leave the player off for an hour
or so, then try again.
No sound.
Volume is in minimum.
Adjust volume to a desired level.
Check wiring connection.
Wiring is not properly
connected.
Sound skips.
The installation angle is
more than 30 degrees.
Adjust the installation angle less
than 30 degrees.
The disc is extremely dirty
or defective disc.
Clean the compact disc, or try
to play a new one.
The operation keys The built-in microcomputer Press the RESET button. Make
do not work.
is not operating properly
due to noise.
Sure the Front panel is properly
fixed into its place.
The radio does not The antenna cable is not
Insert the antenna cable firmly.
work. The radio
station automatic
selection does not The signals are too weak.
work.
connected.
Select a station manually.
12
SANYO MOBILE AUDIO
MODEL ECD-T1535 LIMITED WARRANTY
OBLIGATIONS
In order to obtain warranty service, the product must be delivered to and picked up from an Authorized
Sanyo Factory Service Center at the user’s expense, unless specifically stated otherwise in this
warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by calling
the toll-free number listed below.
For product operation, authorized service center referral, service assistance or problem resolution, call
CUSTOMER INFORMATION 1-800-421-6382
Weekdays 8:00 AM - 5:00 PM Pacific Time
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED AND USED IN THE
UNITED STATES OF AMERICA.
THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER, AND DOES NOT APPLY TO
PRODUCTS USED FOR ANY INDUSTRIAL, PROFESSIONAL OR COMMERCIAL PURPOSE. THE
ORIGINAL DATED BILL OF SALE OR SALES SLIP MUST BE SUBMITTED TO THE AUTHORIZED
SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED.
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO FISHER COMPANY (SFC)
warrants this SANYO product against defects in materials and workmanship for the periods specified
below. SFC will repair or replace (at its option) the product and any of its parts which fail to conform
to this warranty with new or reconditioned products or parts. The warranty period commences on the
date the product was first purchased at retail.
LABOR
1 YEAR
PARTS
1 YEAR
EXCLUSIONS
This warranty does not cover (A) the adjustment of customer-operated controls as explained in the
appropriate model’s instruction manual, or (B) the repair of any product whose serial number has been
altered, defaced or removed.
This warranty does not apply to the cabinet or cosmetic parts, knobs or routine maintenance.
This warranty does not apply to the elimination of car static or motor noise, correction of antenna
problems, or damage to compact discs, speakers, accessories or vehicle electrical systems.
This warranty does not apply to repairs or replacements necessitated by any cause beyond the control
of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from
unauthorized service or parts, improper maintenance, operation contrary to furnished instructions,
shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident,
incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear.
The foregoing is in lieu of all other express warranties and SFC does not assume or authorize any party
to assume for it any other obligation or liability.
THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS) IS LIMITED TO THE TERM OF THIS WARRANTY
IN NO EVENT SHALL SFC BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, OR FOR ANY DELAY IN THE
PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS
CONTROL.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS
AND/OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS, WHICH
VARY FROM STATE TO STATE.
For your protection in the event of theft or loss of this product, please fill in the information below for
your own personal records.
Model No.
Serial No.
Located on back or bottom side of unit)
Date of Purchase
Where Purchased
Purchase Price
13
21605 Plummer Street
Chatsworth, CA91311
ECD-T1535. Issue Number 1.
88-C1007-09
Printed in Hong Kong
|