Operating
Instructions
VACUUM CLEANER
※ Before operating this unit, please read the instructions carefully
IDENTIFICATIONS PARTS
HANDLE
SUCTION HOSE
AIR REGULATOR
RUG/FLOOR
SELECTOR
DUST-FULL INDICATOR
*
TUBE
*
ON/OFF BUTTON
POWER CONTROL
SWITCH
BUTTON FOR SUCTION
HOSE REMOVAL
*
CARRYING HANDLE
FLOOR NOZZLE
CORD REWIND BUTTON
▶ Features marked with * may vary according to model.
ASSEMBLING THE VACUUM-CLEANER READY FOR USE
1) Connect the suction hose to the
2) Connect the suction tubes together
suction tube.
4) Connect the hose clamper to the body
of the cleaner.
3) Connect the nozzle to the suction tube.
2
POWER CORD
1) PULLING OUT
The power cord is long enough to
be drawn out for convenience.
2) REWINDING
Upon finishing cleaning disconnect
the plug from the electrical outlet
and just press the cord rewind button
lightly with your toe.
When removing the power cord from the electrical outlet, grasp the plug, not
the cord.
NOTE :
ON / OFF SWITCH
With the cord plugged into an electrical
outlet, start or stop the vacuum cleaner by
pushing lightly on the switch downward
with your toe.
POWER CONTROL(ONLY VARIABLE CONTROL TYPE)
The vacuuming power can be adjusted to
suit any situation with the electrical power
control.
MIN = For delicate fabrics, e.g.net
curtains.
MAX = For hard floors and heavily
solid carpets.
3
DUST-FULL INDICATOR
If the“Dust-Full”indicator switch changes to“RED”while you are cleaning, the dust bag
requires replacement.
NOTE :
If the“Dust-Full indicator continues to display“RED”even after changing the
dust bag turn the cleaner off and check whether the hose, tube or nozzle is
clogged.
RUG/FLOOR SELETOR
Before use make sure that the position of button is in right position for the type of surface
to be cleaned.
②
①
Push the side ① when cleaning the capets.
Push the side ② when cleaning the floor, tile,mat,etc.
USING THE ACCESSORIES
The accessories are stored at the rear side
of the cleaner.
▶ Dusting brush for furniture,
▶ Crevice tool for radiators, crevice,
shelves, books, etc.
corners, between cushions.
USING THE BLOWER
Located on the right rear side of the
cleaner.
1) Disconnect the hose clamper from the
body of the cleaner.
2) Connect the hose clamper to the blow
hole.
4
PARK POSITION
Located on the top rear side of the
vacuum cleaner, there is a support for a
convenient park position during pauses
when using the nozzle.
TRANSPORTING AND STORING THE VACUUM CLEANER
For easy storage and transportation, this
vacuum cleaner has a clip system built on
the body, which will keep the tube, hose
and nozzle in a vertical position.
REPLACING THE DUST BAG
1) To open the cover of the dust bag com-
partment press the clamper forward loc-
ated at the front of the dust cover.
2) remove the dust bag from the cleaner.
5
3) After removing the used dust bag, insert
the cardboard bag collar of the new dust
bag into the suction inlet to the full.
4) Press the dust cover down gently until
the clamper relocks.
FOR CLOTH FILTER BAG
Use only a designated cloth filter bag:
After using, if the cloth filter bag is full of
dust, clean the cloth filter bag and use it
again.
TROUBLE SHOOTING
PROBLEM
CAUSE
REMEDY
Check cable, plug and
socket.
Motor does not start
No voltage
Suction force is
gradually decreasing
Filter, nozzle, suction
hose or tube is blocked.
Remove the object.
Check that the cord is not Pull the cord out 2~3m &
twisted or wound un- push down the cord,
Cord does not rewind fully
evenly
rewind button.
6
This Vacuum cleaner is approved the following
EMC Directive : 89/336/EEC, 92/31EEC and 93/68/EEC
EN 61000-3-2 : 1995, EN 55014 : 1993 and EN 55104 : 1995
Low Voltage Safety Directive : 73/23/EEC and 93/68/EEC
IEC 335-1, IEC 335-2-2, EN 60335-1 and EN 60335-2-2
(
)
DJ68-40014A REV 0.3
7
|