MX-FS8000
PREMIUM HI-FI Component System
MP3/WMA/CD-DA Playback with CD/USB
user's manual
Imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
Important Information on Use
Disc Storage
Precautions
•
Ensure that the AC power supply in your house complies
with the identification sticker located on the back of your
product.
Install your product horizontally, on a suitable base (furniture),
with enough space around it for ventilation (7.5~10cm).
Do not place the product on amplifiers or other equipment
which may become hot. Make sure the ventilation slots are
not covered.
Do not stack anything on top of the product.
Before moving the product, ensure the Disc Insert Slot is
empty.
To turn off the product completely, disconnect the AC plug
from the wall outlet. Disconnect the AC plug from the wall
outlet if you will leave the device unused for a long period of
time.
During thunderstorms, disconnect the AC plug from the wall
outlet. Voltage peaks due to lightning could damage the
product.
Do not expose the product to direct sunlight or other heat
sources. This could cause the product to overheat and
malfunction.
Protect the product from moisture, and excess heat or
equipment creating strong magnetic or electric fields (i.e.
speakers.).
•
•
•
Do not keep in direct sunlight.
Keep in a cool ventilated area.
Keep in a clean protective jacket.
Store vertically.
Do not allow the discs to become contaminated with dirt.
Do not load cracked or scratched discs.
•
•
•
•
Handling and Storing Discs
If you get fingerprints or dirt on a disc, clean it with a mild
detergent diluted in water and wipe with a soft cloth.
•
•
•
When cleaning, wipe gently from the inside to the outside of
the disc
•
• Condensation may form if warm air comes into contact
with cold parts inside the product. When condensation
forms inside the product, it may not operate correctly. If this
occurs, remove the disc and let the product stand for 1 or
2 hours with the power on.
•
•
•
Disc Types And Disc Format
This product does not support Secure (DRM) Media files.
•
•
•
Disconnect the power cable from the AC supply if the
product malfunctions.
Your product is not intended for industrial use. It is for
personal use only.
CD-R Discs
•
Some CD-R discs may not be playable depending on
the disc recording device (CD-Recorder or PC) and the
condition of the disc.
Condensation may occur if your product or disc has been
stored in cold temperatures. If transporting the product
during the winter, wait approximately 2 hours until the
product has reached room temperature before using.
The batteries used with this product contain chemicals
that are harmful to the environment. Do not dispose of
batteries in the general household trash.
Maintain an open space of approximately 6 inches (15 cm)
on the sides and rear of the system, for ventilation purposes.
Place the loudspeakers at a reasonable distance on either
side of the system to ensure good stereo sound.
Direct the loudspeakers towards the listening area.
•
Use 650MB/74 minute CD-R discs.
Do not use CD-R discs over 700MB/80 minutes as they
may not be played back.
•
•
•
Some CD-RW (Rewritable) media may not be playable.
Only CD-Rs that are properly "closed" can be fully played. If
the session is closed, but the disc is left open, you may not
be able to fully play the disc.
•
•
•
CD-R MP3/WMA Discs
•
•
•
•
•
Only CD-R discs with MP3 files in ISO 9660 or Joliet format
can be played.
MP3 file names should contain no blank spaces or special
characters (. / = +).
Use discs recorded with a compression/decompression
data rate greater than 128Kbps.
Only files with the ".mp3" and ".wma" extensions can be
played.
Only a consecutively written multisession disc can be
played. If there is a blank segment in the Multisession disc,
the disc can be played only up to the blank segment.
If the disc is not closed, it will take longer to begin playback
and not all of the recorded files may play.
For files encoded in Variable Bit Rate (VBR) format, i.e. files
encoded in both low bit rate and high bit rate (e.g., 32Kbps
~ 320Kbps), the sound may skip during playback.
A maximum of 999 files can be played per CD.
Supported Audio Formats (Bit Rate):WMA 56~128kbps
MP3 80~320kbps.
Cautions on Handling and Storing Discs
Small scratches on the disc may reduce sound and picture
quality or cause skipping.
Be especially careful not to scratch discs when handling them.
Holding Discs
•
•
•
•
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not get
on the surface.
•
Do not stick paper or tape on the disc.
•
•
English
3
Contents
Contents
Thank you for buying this SAMSUNG Hi-Fi Component system.
Please take time to read these instructions.
They will allow you to operate your system with ease and take full advantage of its features.
Safety Warnings................................................. 2
How to safely remove the USB device...... 11
Read Before Using the USB Storage
Devices..................................................11
Bluetooth.....................................................11
What is Bluetooth?................................11
To connect the Hi-Fi Component to a
Important Information on Use........................... 3
Precautions.................................................... 3
Cautions on Handling and Storing Discs........ 3
Disc Types And Disc Format.......................... 3
Bluetooth device....................................11
To disconnect the Bluetooth device from
the Hi-Fi Component.............................12
To disconnect the Hi-Fi Component from
the Bluetooth device...............................12
Using My Karaoke .......................................12
10 Skip Function..........................................13
Auto Change Function.................................13
Listening to the Radio..................................13
To Store the Stations You Want.............13
Selecting a Stored Station.....................13
Accessories........................................................ 4
Description ......................................................... 5
Front Panel .................................................... 5
Rear Panel..................................................... 6
Remote Control ............................................. 7
Installing Batteries In The Remote
Control .................................................... 7
Connecting the Speakers .............................. 7
Basic Functions ................................................. 8
The Display function....................................... 8
Playing CD..................................................... 8
Loading Compact Disc............................ 8
CD/MP3/WMA-CD Playback .................. 8
Selecting a Track..................................... 9
Searching for a Specific Music Passage
on a CD................................................... 9
Repeat One or All Tracks on a CD........... 9
A-B Repeat Playback.............................. 9
CD Programming .................................... 9
Viewing or Editing the Programmed
Advanced Functions........................................14
Timer Function.............................................14
Setting the Clock...................................14
Setting the Timer...................................14
Cancelling the Timer..............................15
The Recording Function...............................15
Basic Recording....................................15
Recording Speed ..................................16
Special Sound Effect....................................16
Selecting EQ Mode ...............................16
Using the FOOTBALL Mode..................16
GIGA SOUND Function.........................16
BEAT WAVING Function........................17
DJ BEAT Function .................................17
Track .....................................................10
Playing USB Devices ...................................10
Before you begin! ..................................10
To Select a File from a USB Device........10
To Use High Speed Search ...................10
To Delete a File......................................10
To skip next 10 files...............................11
Move FOLDER ......................................11
Troubleshooting ...............................................18
Specifications ..................................................19
Symbols
Important
Note
Accessories
Check for the supplied accessories below.
USB
CD/
AH59-02553A
User's Manual
Remote Control/ Batteries
FM Antenna
Power Cable
(AH68-02613A)
(AH59-02553A/4301-000116)
(AH42-00021A)
(3903-000467)
•
Figures and illustrations in this user's manual are provided for reference only and may differ from actual product
appearance.
4
English
Description
Front Panel
10 11
12
1
2
3
4
5
6
7 8
9
31
30
13
14
15
16
29
28
27
25 24
23 22 21 20
19
18
17
26
1. Display Panel
21. USB 2 jack for Playing and USB Recording
22. PLAY/PAUSE button
2. BACKWARD SEARCH/SKIP button
3. CD/ Bluetooth button
4. DISC slot
23. AUX IN 1 jack
Connecting an external device such as an MP3
player.
5. GIGA SOUND BEAT button
6. TUNER/AUX button
7. FORWARD SEARCH/SKIP button
8. FOLDER- button
• Connect AUX IN 1 on the front panel of the
product to the Audio Out of the external
device/MP3 player.
• Press the TUNER/AUX button to select the
AUX1.
9. Eject button for Disc
10. MASTER VOLUME
24. MIC jack
11. BEAT WAVING button
12. FOLDER+ button
25. STOP button
26. USB 1 jack for only Playback
27. REMOTE CONTROL SENSOR
28. DISPLAY/ DEMO button
29. USB 1 button
13. POWER button
• Press this button to switch your product on or
off.
14. CHORUS button for DJ BEAT sound effect
15. USB 2 button
30. EQ button
31. FOOTBALL MODE button
16. USB REC button
17. FLANGER button for DJ BEAT sound effect
18. DJ BEAT button
19. WAHWAH button for DJ BEAT sound effect
20. +PANNING button for DJ BEAT sound effect
English
5
Description
Rear Panel
1
2
3
4
5
6
7
1. Cooling fan
6. AUX IN 2 Terminals
• The fan operates while the unit is powered on.
Use an Audio Cable (not supplied) to connect AUX
IN 2 on the product to Audio Out on the external
analog output device.
1.
However, if you set the unit to its minimum volume,
the fan shuts off.
Provide a minimum of 6 inches (15cm) of clear
space in front of the fan when you install the
product.
• Be sure to match connector colors.
• If the external analog output device has only one
Audio Out jack, connect either the left or right jack.
2. POWER
• Press the TUNER/AUX button to select AUX 2.
• Insert only the provided power cable.
• If you do not push any buttons for more than 8
hours when the unit is in AUX mode, the power
turns off automatically.
3. 2.2 CH Speaker Terminals
To achieve the correct sound quality, when you con-
nect the speakers, match the color of the speaker
plugs to the color of the speaker jacks. See below.
1.
7. FM Antenna Terminals
Connect the FM antenna to the FM antenna con-
nector terminal.
1.
L
• LEFT channel (marked , White/Purple).
• RIGHT channel (marked , Red/Purple).
R
Slowly move the antenna wire until you find a
location where reception is good, then fasten it to
a wall or other rigid surface.
2.
Don't force the Purple SUBWOOFER
connector into the White or Red speaker
jack.
•
If reception is poor, you may need to install an
outdoor antenna. To do so, connect an outdoor
FM antenna to the FM socket on the rear of the
system using a 75Ω coaxial cable (not supplied).
3.
4. LED Terminals for Speaker Beat Waving.
The LED Terminals do not distinguish
between the left and right channel.
5. ONLY FOR SERVICE
• This jack is just for testing only. Do not use.
6
English
Description
Remote Control
1. POWER
2. TUNER/AUX
3. USB
4. Number(0~9)
button
11. ENTER
22. TUNING/
ALBUM ,,.
23. EQ
24. AUTO CHANGE
25. REPEAT A-B
26. PAUSE
27. SEARCH
28. CD/Bluetooth
29. BEAT WAVING
30. MUTE
30
29
12. VOLUME (-,+)
13. TUNING MODE
14. TIMER ON/OFF
15. TIMER SET
16. SLEEP
1
USB
CD/
2
3
28
During playback,
press the desired
track number.
The selected
Set a sleep time
to shut off the
product.
4
track is played.
5
6
17. MY KARAOKE
18. MIC VOLUME -, +
19. USB REC
20. DELETE
21. Mono/Stereo
for FM, CD REC
SPEED for CD
Ripping
Turn off
the sound
temporarily.
Press again to
turn the sound
back on.
5. SKIP(-10, +10)
6. SKIP
7. STOP
8. PLAY
9. REPEAT
10. GIGA
27
26
7
8
9
10
11
12
25
24
23
22
Installing Batteries In The Remote Control
21
20
19
13
`
Place batteries in the remote control so
that the polarity of the batteries matches
the polarity of the icons or illustrations in
the batter compartment: (+) to (+) and (–)
to (–).
14
15
16
17
18
AH59-02553A
`
Always replace both batteries at the
same time.
* Battery size: AAA
`
`
Do not expose the batteries to heat or a flame.
The remote control can be used up to
approximately 23 feet (7 meters) in a straight line from the system.
Connecting the Speakers
Recommended speaker setup.
The product may not operate properly if not
☛
installed in accordance with recommended
speaker setup, or exposed to shaking or
external shocks.
Do not stretch the speaker wires or place a
heavy object on them.
☛
English
7
Basic Functions
The Display function
• If no buttons are pressed on the product or remote
control for more than 25 minutes when the product
is in Stop mode, the product will turn off.
You can view all functions available on the dis-
play, adjust the brightness of the display and set
the Display/LED either on or off.
CD/MP3/WMA-CD Playback
Each time you press the DISPLAY/DEMO button,
the display mode will change as follows:
This product is designed to play the following audio
☛
disc types: CD, CD-R, CD-RW, MP3/WMA-CD.
The Dimmer function
◆
The Dimmer function is selected and the display dark-
ens.
1. Insert a disc gently into the disc slot with the disc's
label facing up.
LED OFF
◆
2. The disc will be played automatically.
The LED is turned off while the dimmer function is work-
ing.
Clock ON
The Clock you set is displayed.
Display/LED ON
•
For MP3/WMA-CD audio, it may take several minutes
for the product to finish scanning the disc tracks.
◆
◆
•
If you play a file with an English name or an MP3/
WMA-CD file with an English title, the song title will be
shown in the display. (Titles in other languages will not
be displayed.)
All displays and the LED are turned on.
•
An English-titled track containing a special character
will not be displayed.
The DEMO function
Press the DISPLAY/DEMO button for 5 seconds to
start Demo mode.
➣
<CD Playback Display>
When you press the DISPLAY/DEMO button while the
unit is in Demo mode, the display changes as follows:
Track Indicator
Playtime Indicator
DIMMER
LED Off (unit/speaker)
[time dis-
--:--
➝
➝
3. To adjust the volume:
play]
LED On (unit/speaker)
➝
•
•
Turn the VOLUME control on the product.
-
•
To cancel Demo mode:
Press the DISPLAY/DEMO button for 5 seconds. The
current mode is canceled and the product is turned off.
Press the VOL+ or VOL- button of the remote control.
The volume level can be adjust in 31 steps (VOLUME
MIN, VOLUME01 ~ VOLUME 29, and VOLUME MAX).
• Press TUNER/AUX, CD/Bluetooth or USB button.
The current mode is canceled and the mode is
changed to the mode you selected.
4. Main Unit
To pause playback temporarily, press the p button.
Press p again to continue playing the disc.
-
While displaying DEMO, only the [Power], VOL
buttons and the buttons mentioned above work.
Remote control
To pause playback temporarily, press the PAUSE (#)
button.
- If you connect speaker to AUX1 while displaying
DEMO, sound is produced through AUX1 and you
can use the VOL buttons and
[MUTE].
Press the PLAY (+) button to continue playing the disc.
5. To end playing, press the STOP (
@
) button.
Playing CD
Loading Compact Disc
•
•
If no CD is in the disc slot, “NO DISC” appears on the
display.
The quality of MP3/WMA-CD playback may vary
depending on the condition of the disc or the condition of
the recorder with which the disc was created.
If a disc contains different types of files or unnecessary
folders, you will have problems with playback.
You can play standard CDs that require no adapter.
1. Insert a disc gently into the disc slot with the disc's
label facing up. The disc will be played automatically.
•
• You can load or unload compact discs when the
radio, USB or auxiliary source function is selected.
When you press the EJECT button, the unit
immediately changes from its current mode to the
CD mode.
• If no buttons are pressed on the product or remote
control for more than 3 minutes when the product is
in Pause mode, it will change to Stop mode.
Gently insert a CD into the disc slot. Do not apply
excessive force.
➣
•
Do not apply force to the product or place a heavy
object on the product.
•
Do not insert an out-of-spec or oddly shaped CD
(heart shaped, octangular, etc.). You can damage the
product.
•
Carefully maintain your CDs.
8
English
Basic Functions
Selecting a Track
A-B Repeat Playback
You can select a desired track while the disc is
You can repeatedly play back a designated section
of a CD.
being played
.
To play the previous track
1. Press the REPEAT A-B button at the beginning
of the desired section.
• 'RPT A' will be displayed.
2. Press the REPEAT A-B button at the end of
the desired section.
Press the [ button within 3 seconds after the current
track has started playing.
Press the [ button twice at least 3 seconds after the
current track has started playing.
• 'RPT AB' will be displayed.
To play the next track
3. To cancel REPEAT A-B function, press the
REPEAT A-B button again.
]
Press the
button.
To play the current track from the beginning
• 'OFF' will be displayed.
Press the [ button 3 seconds after the current track
has started playing.
The REPEAT A-B function is available within a
track.
➣
To play the track of your choice
CD Programming
Press the
or
button to move to a desired track.
[
]
This function is not available during playback of an
MP3/WMA-CD.
•
You can also use the number (0~9) buttons on the
remote control to select a track.
• You can program the playback order of up to 24
tracks of your choice.
• However, you must stop playing the CD before
selecting tracks.
Searching for a Specific Music Passage on
a CD
When listening to a CD, you can quickly search
for a specific music passage on a track.
1. While in CD playback mode, press the STOP
(
@) button to stop playing the CD.
Forward Search............................
Backward Search .........................
)
2. Press the ENTER
(
)
button to display the
(
message below:
You can also press and hold the
,
buttons on
[ ]
the product to automatically scan for a track.
(01= program number, ---= track number)
Repeat One or All Tracks on a CD
You can repeatedly play a track, a group of
tracks, or an entire CD.
1. Press the REPEAT button on the remote
control.
Each time you press the REPEAT button, the
repeat mode will change as follows:
MP3: OFF ➝ TRACK ➝ DIR ➝ ALL ➝ RANDOM
CD: OFF ➝ TRACK ➝ ALL➝ RANDOM
2. When you want to stop the repeat function,
press the REPEAT button until "OFF" is
displayed.
• OFF: Cancels repeat playback.
• TRACK: Repeatedly plays the selected track.
• DIR (DIRECTORY): Repeatedly plays all tracks in
the selected folder.
• ALL: Repeatedly plays the entire disc.
• RANDOM: Plays tracks in random order.
English
9
Basic Functions
2. Select the USB mode by pressing the USB 1 or USB 2
button on the product or the USB button on the remote
control.
3. Use the
[
or
]
button to move to a desired
track.
•
•
Press
Press
[
]
to move to the previous track.
to move to the next track.
3. The first file of the first directory plays automatically
.
4. To stop playing
4. Press the ENTER
(
)
button to confirm your
Press the STOP (
@
) button to stop playing.
selection. The selection is stored and
To remove the USB device
If you press the STOP ( @ ) button once
➣
is displayed.
again, you can remove the USB device safe-
ly.
5. To select another track, follow Steps 3 and 4
above.
☛
Do not connect a USB recharger to the USB port
of this product. You can damage the product.
6. Press the PLAY (+) button to play the
programmed tracks.
7. Press the STOP (@) button to stop playing the
programmed tracks, Press the STOP (@) button
again to cancel playing the programmed tracks.
To Select a File from a USB Device
You can select an MP3 file while the product is
playing.
•
If you eject the disc or turn off the product or
change other function mode, your
programming will be canceled.
If you want to move the previous/next track, press the
[,] buttons briefly.
➣
• The unit moves to the previous/next file within the
directory.
• If you press the [,] buttons more times than the
number of files in the directory, the unit moves to the
next directory.
Viewing or Editing the Programmed
Track
You can view a list of programmed tracks and
edit them as you want.
To repeat
1. Press the REPEAT button.
1. If a programmed track is being played, press
Each time you press the REPEAT button, the repeat
mode will change as follows:
OFF ➝ TRACK ➝ DIR ➝ ALL ➝ RANDOM
the STOP (@) button once.
2. Press the ENTER
(
)
button twice to display
2. When you want to stop the repeat function, press the
REPEAT button until "OFF" is displayed.
• OFF: Cancels repeat playback.
the message below:
• TRACK: Repeatedly plays the selected file.
• DIR (DIRECTORY): Repeatedly plays all files in the
selected folder.
(01= program number, 002= track number)
3. Repeatedly press the ENTER
(
)
button until
the desired track is displayed.
• ALL: Repeatedly plays all files.
• RANDOM: Plays files in random order.
4. Press the
[
or
]
button to select a different
button to confirm your
track.
To Use High Speed Search
5. Press the ENTER
(
)
You can search the desired section quickly while
the product is playing.
selection.
6. To play the programmed tracks, press the Play
) button.
1. Press the
,
button.
( )
(+
• Each time you press the button, you will move
forward/backward fast.
Playing USB Devices
Sound does not output during a high speed search.
☛
Connect an external storage device such as a USB
flash memory or external HDD (Hard Disk Drive) to
the product. You can play files in MP3/WMA format.
To Delete a File
You can delete a file from your USB device.
Select a file you want to delete.
1.
2.
3.
Press the DELETE button on the remote control.
Before you begin!
Press the [,] buttons on the product or remote
control to select YES/NO.
1. Connect the external USB storage device to your
product.
10
English
Basic Functions
Press the ENTER button on the remote control.
The selected file will be deleted.
4.
Bluetooth
You can use a Bluetooth device to enjoy music with
high quality stereo sound, all without wires!
The NTFS file system is not supported.
☛
To skip next 10 files
What is Bluetooth?
1. Press the +10 or -10 button while in playback mode.
Bluetooth is a technology that enables Bluetooth
compliant devices to interconnect easily with each
other using a short wireless connection.
The unit will skip as many as 10 tracks forward or 10
tracks back from the current track.
Move FOLDER
•
A Bluetooth device may cause noise or malfunction,
depending on usage, if:
Press the remote control's TUNING/ALBUM
,
,
.
button
-
A part of your body is in contact with the receiving/
transmitting system of the Bluetooth device or the Hi-Fi
Component.
or the product's FOLDER -, + button to move to the previ-
ous/next folder.
-
-
It is subject to electrical variation from obstructions
caused by a wall, corner, or office partitioning.
It is exposed to electrical interference from same
frequency-band devices including medical equipment,
microwave ovens, and wireless LANs.
How to safely remove the USB device
1. Press the (
@
) button twice while the USB is playing or
press the (
@
) button once when play is stopped.
2. When the REMOVE message appears on the display,
•
•
Pair the Hi-Fi Component with the Bluetooth device while
they are close together.
The greater the distance between the Hi-Fi Component and
the Bluetooth device, the worse the quality. If the distance
exceeds the Bluetooth operational range the connection is
lost.
remove the USB device.
Read Before Using the USB Storage
Devices
• Some USB devices may not work properly with this
product.
• This product only supports external HDD's that are
formatted in the FAT file system.
• USB 2.0 HDDs should be connected to a separate power
source. Otherwise, the USB 2.0 HDDs will not work.
• If multiple USB external storage devices are connected
together, only the MP3 files in the first HDD will be
played.
•
•
In poor reception-sensitivity areas, the Bluetooth connection
may not work properly.
The Bluetooth connection only works when the Bluetooth
device is close to the set. The connection will be
automatically cut off if the Bluetooth device is out of range.
Even within range, the sound quality may be degraded by
obstacles such as walls or doors.
•
This wireless device may cause electric interference during
its operation.
•
Files with DRM are not supported. Digital Right
Management (DRM) restricts unauthorized access to a DRM
file so that the copyright of the file is protected from piracy.
To connect the Hi-Fi Component to a
Bluetooth device
• Even if a file has an .mp3 extension, the file cannot be
played if it is formatted in MPEG layer 1 or 2.
• Do not use an unrecognized USB hub.
• Only the first 15 characters of a MP3/WMA file are
displayed.
• Only removable HDDs with less than 160GB are
supported. Depending on the device, a 160GB or more
removable HDD may not be supported.
• It can take several minutes for the product to recognize
the files on some USB devices.
Before you begin, confirm that your Bluetooth
device supports the Bluetooth-compliant stereo
headset function.
Press the CD/ Bluetooth button of the Hi-Fi Component
to display the BLUETOOTH message.
1.
•
You will see WAIT for a few seconds and then READY
on the front display of the Hi-Fi Component.
• Some USB devices (USB HDDs, in particular) may cause
a delay when moving from track to track.
• With USB storage devices supporting USB VER1.1 only,
the product may access files slowly or may not recognize
the file properties.
• The maximum electrical current supported by external
USB devices via each USB port is 0.5A (based on DC 5V).
Select the Bluetooth menu on the Bluetooth device you
want to connect. (Refer to the Bluetooth device's user
manual.)
2.
Select the Stereo headset menu on the Bluetooth device.
3.
4.
•
You will see a list of scanned devices.
Select "[Samsung] HI-FI XXXXXX" from the list.
When the product is connected to the Bluetooth
•
•
If there is no USB connection or STOP mode lasts for more
than 25 minutes, the product will automatically turn off.
A certain USB, digital camera device, USB card reader,
iPod, iPhone or Smart Phone may not be supported.
device, it will display CONNECTED
➞
BLUETOOTH
on the front display.
•
English
11
Basic Functions
•
If the Bluetooth device has failed to pair with the
product, delete the previous “[Samsung] HI-FI XXXXXX”
found by the Bluetooth device and have it search for
the product again.
To disconnect the Hi-Fi Component
from the Bluetooth device
Press the CD/Bluetooth button on the front panel
of the Hi-Fi Component to switch from Bluetooth
mode to another mode or turn off the Hi-Fi Compo-
nent.
Play music on the connected device.
5.
•
You can listen to the music playing on the connected
Bluetooth device over the Hi-Fi Component system.
In Bluetooth mode, some model's Play/Repeat/Stop/
Next/Back functions are not available.
•
The connected Bluetooth device will wait a certain amount
of time for a response from the Hi-Fi Component before
terminating the connection. (Disconnection time may differ,
depending on the Bluetooth device)
•
The product only supports Middle Quality SBC data (up
to 237kbps@48kHz), and does not support High Quality
SBC data ([email protected]).
➣
•
The currently connected device will be disconnected.
In Bluetooth connection mode, the Bluetooth connection
will be lost if the distance between the Hi-Fi Component
and the Bluetooth device exceeds 16.25 feet (5 meters).
•
The AVRCP feature is not supported.
➣
•
Connect only to a Bluetooth device that supports the
A2DP (AV) function.
•
If the Bluetooth device comes back into the effective
range after disconnecting, you can restart the Hi-Fi
Component to restore the pairing with the Bluetooth
device.
•
You cannot connect to a Bluetooth device that
supports only the HF (Hands Free) function.
•
•
Only one Bluetooth device can be paired at a time.
Once you have turned off the Hi-Fi Component and
pairing is terminated, pairing will not be restored
automatically. To reconnect, you must pair the device
again.
•
The Hi-Fi Component automatically turns off after 25
minutes in the Ready mode.
•
The Hi-Fi Component system may not search or
connect properly in the following cases:
Using My Karaoke
-
If there is a strong electrical field around Hi-Fi
Component.
If several Bluetooth devices are simultaneously paired
with Hi-Fi Component.
If the Bluetooth device is turned off, not in place, or
malfunctions.
You can use the MY Karaoke function to sing
along with your favorite CDs and USB tracks.
-
-
1. Connect the microphone to the MIC jack on the front
of the product.
`
If your microphone plug is larger than the 3.5 mm
MIC jack, you need a Connector-Adaptor (not
supplied) to complete the connection.
•
Note that such devices as microwave ovens, wireless
LAN adaptors, fluorescent lights, and gas stoves use
the same frequency range as the Bluetooth device,
which can cause electric interference.
-
First, connect the Connector-Adaptor to the MIC jack
on the front of the product,
-
Second, connect the microphone (with larger jack) to
the Connector-Adaptor.
To disconnect the Bluetooth device from
the Hi-Fi Component
2. Press the MIC VOL-, + button on the remote
control to adjust the volume of the microphone.
You can disconnect the Bluetooth device from the
Hi-Fi Component. For instructions, see the
Bluetooth device's user manual.
3. Press the MY KARAOKE button on the remote
control to suppress the vocal if you need. Each time
the button is pressed, the selection is changed as
follows:
•
•
The Hi-Fi Component will be disconnected.
When the Hi-Fi Component is disconnected from the
Bluetooth device, the Hi-Fi Component will display
MY KARAOKE ON
➞
MY KARAOKE OFF
`
If you hear strange noises (squealing or howling)
while using the Karaoke feature, move the
microphone away from the speakers. Turning down
the microphone's volume or the speaker volume is
also effective. Do not aim the MICROPHONE
towards the SPEAKERS.
DISCONNECTED
➞
READY on the its display.
`
`
The microphone does not operate in the AUX and
TUNER mode.
If you connect a microphone, GIGA SOUND
automatically turns off. To turn Giga Sound back on,
you must remove the microphone, and then press
the Giga Sound button.
12
English
Basic Functions
`
`
`
When My Karaoke is on, EQ and GIGA SOUND do
not work.
When you stop playing the CD or USB, My Karaoke
turns off automatically.
My Karaoke is only available when a microphone is
connected to the HI-Fi Component.
Listening to the Radio
To Store the Stations You Want
You can store up to:
15 FM stations.
1. Select FM by pressing the TUNER/AUX button.
10 Skip Function
2. To search for a station, press the TUNNING MODE
button on the remote control or the STOP button on
the product one or more times until MANUAL is
displayed.
Press the +10 or -10 button while the unit is in
playback mode. The unit will skip as many as 10
tracks forward or 10 tracks back from the current
track.
3. Select a station by:
• Pressing the TUNING/ALBUM , or . button on
the remote control to find a station.
Auto Change Function
4. Press the MO/ST button to switch between stereo and
mono.
You can set the product to play a disc, and then
play files on USB devices connected to USB 1
and USB 2 continuously.
• In a poor reception area, select MONO for a
clear, interference-free broadcast.
• This applies only when you are listening to an FM
station.
1. Press the AUTO CHANGE button on the remote.
Each time you press this button, the mode
switches as follows:
5. If you do not want to store the radio station found, go
back to Step 3 and search for another station.
Otherwise:
;
AUTO CHANGE OFF
AUTO CHANGE ON
a. Press the ENTER button.
b. Or, press the TUNING/ALBUM button on the
remote control to select a program number.
•
When AUTO CHANGE is "ON",
-
The Hi-Fi Component will play a disc in the disc slot,
then play files on a USB device connected to USB1,
and then play files on a USB device connected to
USB2. The files will be played continuously.
If you press the POWER button, function change
button, or the EJECT button, the AUTO CHANGE
function automatically turns "OFF".
c. Press the ENTER button to save the preset.
6. To store other radio frequencies, repeat Steps 3, 4,
and 5.
-
Selecting a Stored Station
-
-
Recording is disabled.
The REPEAT and SLEEP functions are automatically
set to OFF and are unavailable.
To listen to a stored station, follow these steps:
1. Select FM by pressing the TUNER/AUX button on
the product or remote control.
2. Press the TUNING MODE button on the remote
control until “PRESET” is displayed.
3. Press [,] button on the main unit or TUNING/
ALBUM , , . on the remote control to select a
preset number.
-
The CD REC SPEED, USB REC, PROGRAM and
DELETE functions unavailable.
•
•
If you disconnect a playing USB device, the AUTO
CHANGE function automatically turns "OFF".
If there's no device in USB1, the function automatically
switches to USB2.
English
13
Advanced Functions
Timer Function
4. Set the timer switch-off time.
a
b
c
d
Press the TUNING/ALBUM , or . button to
set the hours.
Press the ENTER (
) button.
Setting the Clock
Result: The minutes flash.
Press the TUNING/ALBUM , or . button to set
the minutes.
For each step, you have a few seconds to set the
required options. If you exceed this time, you must
start again.
Press the ENTER (
) button.
Result: VOLUME XX is displayed, where XX corre-
sponds to the volume already set.
1. Press the TIMER SET button on the remote
5. Press the TUNING/ALBUM , or . button to adjust the
volume level and press the ENTER ( ) button.
control twice. "CLOCK SET" is displayed.
2. Press the ENTER (
) button on the remote
Result: The source to be selected is displayed.
control. The hour flashes.
6. Press the TUNING/ALBUM , or . button to select the
•
•
Increase the hours: TUNING/ALBUM ,
Decrease the hours: TUNING/ALBUM .
source the Hi-Fi Component will play when it switches
on.
If you select...
You must also...
3. When the correct hour is displayed, press the
ENTER ( ) button, and then the minutes flash.
FM (radio) ................... a Press the ENTER (
)
button.
•
•
Increase the minutes: TUNING/ALBUM ,
Decrease the minutes: TUNING/ALBUM .
b
Select a preset station by
pressing the TUNING/
ALBUM , or . button.
4. When the correct minute is displayed, press the
ENTER ( ) button, and then "TIMER PLAY
CD (compact disc) .....Load a compact disc.
USB ............................Connect the USB device.
SET" appears in the display.
7. Press the ENTER (
) button.
Setting the Timer
Result: TIMER REC SET (Do you want to record?) is
displayed.
The timer enables you to switch the product on or
off at specific times automatically.
8. Press the ENTER (
) button.
Result: REC SET YES/NO is displayed. You can press
the TUNING/ALBUM , or . button to select
REC YES or REC NO, and then press
ENTER button.
•
Before setting the timer, check that the current time
is correct.
For each step, you have a few seconds to set the
required options. If you exceed this time, you must
start again.
If you no longer want the product to be switched
on or off automatically, you must cancel the timer
by pressing the TIMER ON/OFF button.
•
If you select REC NO, tuner timer recording will not
activate, even if you have already set the tuner timer
recording.
1)
•
If you select REC YES, you can set the tuner timer
recording on and off times.
2)
Example: You want to wake up to music every morn-
ing.
Press the ENTER (
) button.
a.
Result: ON TIME is displayed for a few seconds.
You can set the tuner timer recording switch-
on time.
1. Press the TIMER SET button until TIMER PLAY SET is
displayed.
Press the ENTER (
) button.
2. Press the ENTER (
) button.
b.
Result: OFF TIME is displayed for a few seconds.
You can set the tuner timer recording switch-
off time.
Result: ON TIME is displayed for a few seconds. You
can set the timer switch-on time.
3. Set the timer switch-on time.
a
b
c
d
Press the TUNING/ALBUM , or . button to
set the hours.
Press the ENTER (
) button.
Result: The minutes flash.
Press the TUNING/ALBUM , or . button to
set the minutes.
Press the ENTER (
) button.
Result: OFF TIME is displayed for a few seconds.
You can now set the timer switch-off time.
14
English
Advanced Functions
•
•
•
The maximum length of time for tuner timer recording is
5 hours.
If the timer switch on and off times are identical, the
word ERROR is displayed.
USB 1
• Connect the USB device with the files you want to
record to the USB 1 jack.
• Press the USB button to select USB 1.
• Play a song from the USB 1.
You can use the [, ] buttons on the product
instead of the TUNING/ALBUM , or . button to
make adjustments in Steps 3 through 8.
If the switch-on or -off time is the same as the timer
recording time, only the switch-on or -off time is
effective, and the timer recording is not applied.
When you use the auto timer, you may need an
additional step to use a CD or USB device with it,
depending on the disc (or device). Consequently, it is
easier to use the tuner instead.
External Source
•
•
• Connect an External device/MP3 player to the
product.
• Press the TUNER/AUX button to select <AUX IN 1 or
AUX IN 2>.
• Play a song from the external device.
3. Press the USB REC button on the remote control to
start recording.
•
If you select CD or USB mode when there is no disc or
no USB in the product, it will automatically change to
TUNER mode.
CD
•
Track recording message is displayed and CD
recording starts.
• If you want to record all the tracks on the disc,
press and hold the USB REC button. Then, Full CD
recording message will be displayed.
Cancelling the Timer
After having set the timer, it will start automatically
as shown by the TIMER ON message on the display.
If you no longer want to use the timer, you must can-
cel it.
RADIO
•
Tuner recording message is displayed and recording
starts.
To cancel the timer, press the TIMER ON/OFF button once.
To restart the timer, press the TIMER ON/OFF button
again, once.
CD-ROM/ USB
•
“FILE COPY” is displayed and recording starts.
You can also copy a folder including MP3/WMA files
to a device on USB 2. if you press and hold the USB
REC button while the system plays an MP3 or WMA
file in a folder, your system will display "FOLDER
COPY".
•
•
When you select the TIMER OFF mode, the TIMER
RECORDING and TIME functions are not available.
•
•
When the recording is done, “STOP” will be displayed.
If there is a file with the same name on the USB 2
device, "EXIST FILE" is displayed, and the function is
canceled.
If a microphone is connected to the product and you
press the USB REC button, you activate the MP3
Recording function, not the Copy function.
When you press the USB REC button for a second,
file copy starts. When you press the USB REC button
for a few seconds, folder copy starts.
The Recording Function
Basic Recording
•
•
You can record from a CD, a USB device, a radio
broadcast, or an external source to a USB storage
device.
1. Connect the external USB storage device to a USB
(
) jack on your product.
External Source
2. Play a disc or USB, turn on the radio and select a
station, or connect the external source to your
product as described below.
•
AUX recording message is displayed and recording
starts.
CD/USB1(MP3) & MIC
CD
•
MP3 recording message is displayed and recording
starts.
• Press the CD button on the product to select the CD
function.
• Insert a CD gently into the disc slot.
• Use the CD selection ( [ or ] ) buttons to select the
desired song.
4. To stop recording, press the STOP (@) button. The
recording is automatically saved as an MP3 file.
5. After the recording is finsihsed, a directory named
“RECORDING”(CD-DA), “CD COPY”(CD-ROM/
USB(WMA/MP3)), “TUNER RECORDING”, “AUX
RECORDING” or “MP3 RECORDING” is created in
your device.
TUNER
•
•
Select FM by pressing the TUNER/AUX button.
Select the radio frequency you want to record.
English
15
Advanced Functions
•
•
•
WMA/MP2 files can only be copied. They cannot be
recorded.
OFF;FLAT;RANCHERA;SAMBA;CUMBIA;
HABANERA;BOOMBA;REGGAE;MERENGUE;
SALSA;PARTY;POP;HIP HOP;ROCK;JAZZ;
CLASSIC;ELECTRONIC;MP3 ENHANCER;
VIRTUAL SOUND;USER EQ
Do not disconnect the USB device or the AC Cord during
recording. You can cause file damage.
If you disconnected the USB device during recording,
the product will turn off and you will not be able to delete
the file that has been recorded. If his occurs, connect the
USB device to a PC, back up the USB data to the PC,
and then reformat the USB device.
If the USB device does not have enough memory, “NOT
ENOUGH MEMORY” will appear on the display.
The Recording function supports the FAT file systems
only. The NTFS file system is not supported.
When you use the CD high speed search function, the
CD recording function is unavailable.
2. To set the BASS, MID (Middle) and TREB (Treble)
levels manually, select USER EQ, and then press
the ENTER button.
Result: The BASS level (left numeric) flashes.
Press the TUNING/ALBUM , or . button to
select a level from -06 to 06.
•
•
•
Then, press the ENTER button.
Result: The MIDDLE level (middle numeric) flashes.
Press the TUNING/ALBUM , or . button to
select a level from -06 to 06.
•
•
With some USB devices, recording time may be longer.
In the Program mode, you can't use the CD recording
function.
When the Recording function is active, the EQ and
GIGA SOUND functions automatically turn off and are
unavailable.
Then, press the ENTER button.
Result: The TREBLE level (right numeric) flashes.
Press the TUNING/ALBUM , or . button to
select a level from -06 to 06.
•
Then, press the ENTER button.
Result: Setting is complete.
•
•
•
During a CD recording, the REPEAT function automatically
turns off and is unavailable.
If you use the MIC function during a CD recording, the
voice from the microphone will be recorded.
You can not record audio from the radio when searching
for a station or if there are no frequencies available when
the product is set to Tuner mode.
Note that setting the input level too loud when recording
music from an external device through the AUX or USB
channel may introduce noise into the recording. If this
occurs, lower the external device’s volume level.
•
•
When the Hi-Fi Component is recording, the EQ function is
turned off automatically and is unavailable.
If no buttons are pressed within 8 seconds, your settings will
automatically be cancelled and the previous settings will be
saved.
•
The EQ mode may be different depending on your region.
•
Using the FOOTBALL Mode
The football mode brings greater realism to sports
broadcasts.
Recording Speed
1. Press the FOOTBALL MODE button on the product.
Each time you press the CD REC SPEED button
on the remote control, the recording speed will
change as following:
Each time you press the button, the sound mode
switches as follows:
FOOTBALL OFF ; FOOTBALL MODE 1 ;
RECORD SPEED x 1 ; RECORD SPEED x 4
FOOTBALL MODE 2
•
•
•
•
When you record from the tuner or an external source, you
cannot change the recording speed.
If you select RECORD SPEED X 4, sound is not produced
during the recording.
If you connect the microphone, you have one recording speed
mode available: RECORD SPEED X1.
During recording, if you disconnect the microphone, the
recording will stop. If you reconnect the microphone, the
recording will not restart.
•
The FOOTBALL mode may be different depending on your
region.
GIGA SOUND Function
The GIGA SOUND function amplifies the bass
sound and provides twice the bass for powerful,
realistic sound.
1. Press the GIGA SOUND BEAT button on the main
unit or the GIGA button on the remote control.
Each time you press the button, the sound mode
switches as follows:
Special Sound Effect
Selecting EQ Mode
GIGA SOUND BEAT ; GIGA SOUND OFF
Your Hi-Fi Component system provides predefined
equalizer settings that are optimized for particular
music genre. You can also adjust the bass, middle
and treble levels manually.
2. To cancel this function, press the GIGA SOUND
BEAT button until the “OFF” is displayed.
•
The GIGA SOUND mode may be different depending
on your region.
1. Press the EQ button.
Each time you press this button, the sound mode will
switch as follows:
16
English
Advanced Functions
BEAT WAVING Function
The Beat Waving function lets you change the
Speaker LED display mode.
1. Each time you press the BEAT WAVING button on
the product, the Speaker LED display mode
changes as follows:
PARTY 1 ; PARTY 2 ; FUN 1 ; FUN 2 ; PURE ;
FRESH ; LOVE ; JOY ; SUNSET ; SUNRISE ;
NATURE 1 ; NATURE 2 ; WAVE 1 ; WAVE 2 ;
;
AURORA OFF
•
If you select BEAT WAVING OFF, all the speaker LED
displays are turned off.
DJ BEAT Function
The DJ Beat function lets you turn on the
FLANGER, PANNING, CHORUS, and WAHWAH
sound effect functions. The level of each effect is
adjustable.
☛
The set scope is [-15 ~ +15] and the initial set up
values are all 0.
FLANGER : Creates a vibration similar to the sound of a jet
engine revving up and down.
PANNING : Increases the left and right speaker's output in
turn and makes it seem as if the sound is moving
from side to side.
WAHWAH : Creates a 'Wah~ Wah~’ effect.
CHORUS : Creates a vibration that sounds like a singing
chorus.
1. To set the desired effect, press the FLANGER,
PANNING, CHORUS, or WAHWAH button on the
product.
•
The red LED turns on around the button you pushed
and around the DJ BEAT button.
•
You can control the intensity of the effect with the
Volume Jog. To control the volume, press the product's
DJ BEAT button.
•
•
To cancel an effect, press the effect's button again.
To change to a different effect, press another effect
button.
•
•
You can apply the PANNING effect to the FLANGER,
CHORUS, or WAHWAH effects.
To apply the PANNING effect to another effect, press
the PANNING button when the other effect is active or
press another effect button when the PANNING effect
is active.
•
•
Use the Volume JOG to control the intensity of the
effect that was activated last. For example, if you
activated the WahWah effect and then the Panning
effect, the Volume Jog will control the Panning effect.
To control the intensity of the effect you applied first,
press the button of effect that you applied last to turn
it off. Then, you can use the Volume Jog to control the
intensity of the first effect.
English
17
Troubleshooting
Troubleshooting
Refer to the chart below when this product does not function properly. If the problem you are
experiencing is not listed below or if the instruction below does not help, turn off the product,
disconnect the power cord, and contact the nearest authorized dealer or Samsung Electronics Service
Center.
Symptom
Check/Remedy
I cannot eject the disc.
• Is the power cord plugged securely into the outlet?
• Turn off the power and then turn it back on.
Playback does not start
immediately when the
• Are you using a deformed disc or a disc with scratches on the surface?
• Wipe the disc clean.
Play/Pause button is pressed.
Sound is not produced.
• No sound is heard during fast playback, slow playback, and step
motion playback.
• Are the speakers connected properly? Is the speaker setup correctly
customized?
• Is the disc severely damaged?
The remote control does not
work.
• Is the remote control being operated within its operational angle and
distance range?
• Are the batteries drained?
• The product is not working.
(Example: The power goes out or
the front panel key doesn't work
or you hear a strange noise.)
• Run the reset function. With the “NO DISC” message on the display of
the product and no disc in the disc slot, press and hold the STOP (@)
button on the product for more than 5 seconds.
Using the RESET function will erase all stored settings.
Do not use this unless necessary.
• The product is not working
normally.
Can't receive radio broadcast.
• Is the antenna connected properly?
• If the antenna's input signal is weak, install an external FM antenna in an
area with good reception.
Turn off automatically after
displaying "PROTECT"
• Check the power in use is within the range of the power which specified
on the rear label of the product.
• If "Voltage Selector" is on the rear panel, check the power is same with
the voltage that you set manually.
18
English
Specifications
Specifications
AC110-120V~ 50/60Hz 137W
6.1 Kg (13.4 pounds, 215.17 ounces)
55 Kg (121.3 pounds, 1940.07 ounces)
21.7 in. x 8.4 in. x 14.4 in. (550 (W) x 212 (H) x 367 (D) mm)
25.5 in. x 25.7 in. x 17.3 in. (648 (W) x 652 (H) x 440 (D) mm)
41° ~ 95° F (+5°C~+35°C)
10 % to 75 %
Power Requirements
Main unit
Weight
Speaker
Main unit
Speaker
General
Dimensions
Operating Temperature Range
Operating Humidity Range
Signal/Noise ratio
55 dB
10 dB
FM Tuner
CD Disc
Usable sensitivity
1 %
Total harmonic distortion
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
CD : 12 cm (COMPACT DISC)
575W/CH (4Ω)
575W/CH (4Ω)
22Hz~20KHz
Front speaker output
Subwoofer output
Frequency range
S/N Ratio
Amplifier
65 dB
Channel separation
Input sensitivity
60 dB
800mV (AUX)
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
- Design and specifications are subject to change without prior notice.
- For information on the power supply and power consumption, r
efer to the label attached to the product.
English
19
WARRANty
LIMItED WARRANty tO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc. (SAMSUNG) and delivered
new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in
materials and workmanship for a limited warranty period of:
One (1) year Parts and Labor*
(*90 Days Parts and Labor for Commercial Use)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United
States. To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures.
Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be
presented upon request as proof of purchase to SAMSUNG or SAMSUNG's authorized service center. Transportation of the
product to and from the service center is the responsibility of the purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned
parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products
become the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the
remaining original warranty, or ninety (90) days, whichever is longer.
SAMSUNG’s obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand name are set forth in the
applicable end user license agreement. Non-SAMSUNG hardware and software products, if provided, are on an “AS IS” basis.
Non-SAMSUNG manufacturers, suppliers, publishers, and service providers may provide their own warranties.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to
the extent otherwise expressly provided for in this statement, noncommercial use of this product, and shall not apply to the
following, including, but not limited to: damage which occurs in shipment; delivery and installation; applications and uses for
which this product was not intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse,
neglect, fire, water, lightning or other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies,
accessories, applications, installations, repairs, external wiring or connectors not supplied and authorized by SAMSUNG, or
which damage this product or result in service problems; incorrect electrical line voltage, fluctuations and surges; customer
adjustments and failure to follow operating instructions, cleaning, maintenance and environmental instructions that are covered
and prescribed in the instruction book; product removal or reinstallation; reception problems and distortion related to noise,
echo, interference or other signal transmission and delivery problems. SAMSUNG does not warrant uninterrupted or error-free
operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED
ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH
RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF
REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF
THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING
THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER
AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR
INABILITY TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG.
THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS
PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
To obtain warranty hardware service, please contact SAMSUNG customer care center.
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
WRITE
1-800-SAMSUNG
(726-7864)
Samsung Electronics America, Inc. 85
Challenger Road Ridgefield Park, NJ 07660
U.S.A
AH68-02613A-00
|