CS Series Microphone
Neodymium Dynamic Capsule Select Microphone
with CS1 Vocal and CS2 Instrument Capsules
CS Series · Capsule Select Microphone
Features
The Samson CS Series utilizes state-of-the-art microphone technology and is engineered to the finest
detail. Here are some of its main features:
•
Neodymium dynamic handheld mircrophone with CS1 vocal and CS2 instrument selectable capsules
•
CS1 microphone capsule tailored for vocal performance with minimal proximity effect and balanced
frequency response for on and off axis performance
•
•
•
•
•
•
•
CS2 microphone capsule specially designed for close-miking instruments with high SPLs
Ultra sensitive, neodymium element picks up the nuances of any performance
Tight, super cardioid polar pattern for maximum gain before feedback
Extended range frequency response for optimum reproduction and exceptionally clear, crisp sound
Rugged, zinc alloy die-cast case ensures reliable performance and greatly reduced handling noise
Gold-plated XLR Connector
Microphone clip and zippered carry case are included
3
Changing the Capsule
1.
Turn down the level control of the device the CS Series Microphone is connected and disconnect the XLR
cable from the microphone.
2.
3.
4.
Unscrew the installed capsule, removing the entire grill and element from the base.
Screw in the desired CS capsule, making sure the threads are aligned before tightening.
Ensure the capsule is completely secured to the base before using, as any vibration may loosen the capsule,
add handling noise, and result in signal loss.
5.
Reconnect the XLR cable and slowly raise the volume of the microphone until the desired level is reached.
Caring for your CS Microphone
Your CS Series Microphone’s rugged design and gold-plated connectors are made to withstand years of extreme
usage, but to ensure your microphone and capsule will not become damaged, always store the microphone and
additional capsule in the provided protective case.
To clean your microphone, wipe it down with a damp cloth or remove the grill and rinse with plain water. If
needed, use a mild cleaner (such as dishwashing liquid soap) to remove any odors or stains. Never use abrasive
cleaners as they may damage the microphone’s finish. Should the XLR, or gold capsule ring connectors ever
become oxidized, use a deoxidizing solution. Make sure the connectors are completely dry before affixing the
capsule or connecting an XLR cable.
4
CS Series · Capsule Select Microphone
Operating Notes
Polar Pattern
Every microphone has a characteristic polar pattern that determines the microphone’s sensitivity to signals coming from 360° around the micro-
phone. The CS1 and CS2 capsules are unidirectional supercardioid, meaning that they predominantly pick up and reproduce sound originating
directly in front of the microphone, with a coverage angle of approximately 115°, and rejects off-axis ambient sounds.
Feedback Rejection
When using a microphone in a live situation, you may encounter feedback issues. Feedback is the characteristic howling sound
that occurs when a mic is placed too close to a loudspeaker, and the signal from the loudspeaker is fed into the mic, then into
the loudspeaker, etc., until an oscillating tone is generated. When using floor monitors with the CS Series microphone, the
monitors should be placed about 55° off of the rear axis. This same consideration should be made when using the CS Series
microphones on drum kits or guitar amplifiers; the microphone should be positioned to avoid picking up sounds from the rear
of the microphone.
Proximity Effect
Proximity effect is an audio phenomenon that is inherent to uni-directional microphone designs. As the microphone is brought close to the sound
source (approximately ¼”) there is boost to the bass frequencies below 100Hz. As you become aware of this boost in frequencies, you can use it to
your advantage to enhance vocals, and increase the warmth of instruments.
Guidelines for Microphone Use
•
•
•
•
•
Aim the microphone at the desired source. Keep unwanted sound sources at ~126° angle from the front of the microphone.
Place the microphone as close to the sound source as possible.
Use the proximity effect to your advantage: the closer the mic is to the sound source, the more emphasized the bass response will be.
Use a windscreen to suppress unwanted wind noise.
Never cup your hand over the microphone grill, as this will affect the response of the microphone, and can induce feedback.
5
Microphone Placement
Application
Remarks
Vocals (CS1)
<2 inches from lips for a full sound with increased low frequency output
2–4 inches from lips for a balanced natural sound
Electric Guitar Amplifier (CS2) ≤1 inch from the grill for a punchy sound with increased isolation
1–4 inches from the grill for a balanced sound
Positioning the microphone towards the center of the speaker cone produces a brighter tone.
Positioning the microphone towards the edge of the speaker cone produces a mellower tone, and minimizes
hiss from the amplifier.
Acoustic Guitar (CS2)
Snare Drums (CS2)
1–3 inches from the sound hole for increased isolation with increased low frequency output
3–8 inches from the sound hole for natural sound with minimal leakage
3–8 inches from the bridge to reduce pick noise
1–2 inches from the top of the drum head for a punchy sound
1–2 inches from the bottom of the snare for a snappy sound
When using multiple microphones, be mindful of frequency and phase cancellation
Tom-Tom Drums (CS2)
1–2 inches from the top of the drum head aimed towards the top of the head
Brass and Woodwinds (CS2)
1–2 feet from bell, off-axis for a balanced tone
≤1 foot for increased isolation in live situations, and a brighter tone
6
CS Series · Capsule Select Microphone
Specifications
CS1Neodymium Vocal Capsule
Frequency Response
Sensitivity
Rated Impedance
Polar Pattern
Max SPL
60Hz~18kHz
-55 2dBV/Pa
250 ohm
Super Cardioid
150dB
Net Weight
Size
246g
Ø 54×180mm
CS2 Neodymium Instrument Capsule
Frequency Response
Sensitivity
Rated Impedance
Polar Pattern
Max SPL
50Hz~18kHz
-56 2dBV/Pa
250 ohm
Super Cardioid
150dB
Net Weight
Size
246g
Ø 47×170mm
Accessories
Mic Clip, Zippered Case
v1.2 ©2012 Samson Technologies Corp.
7
Samson Technologies Corp.
45 Gilpin Avenue
Hauppauge, New York 11788-8816
Phone: 1-800-3-SAMSON (1-800-372-6766)
Fax: 631-784-2201
samsontech.com
|