Owner’s Manual
Headphone Features
1. Multi-function button
2. Volume Up button
3. Volume Down button
4. Fast-Forward (Next Track) button
5. Rewind (Previous Track) button
6. Play/Pause/Phone button
7. Indicator Lights
8. NFC Area
9. Micro-USB charge port
10. 3.5mm auxiliary audio input
RTE 2 Bluetooth® Headphones
3
Quick Start
Fully charge your RTE 2 Bluetooth Headphones before first use.
1.
2.
To charge your headphones plug the included USB cable into the USB port of your computer or a USB 5-volt adapter (smart phone charger) and
plug the smaller end of the cable into the bottom of the right ear cup of your headphones. You will see a green light appear just above the charge
port of your headphones.
When the battery is fully charged the green light indicator above the charge port will turn off.
Pairing your headphones to your device for wireless operation via Bluetooth:
1.
With the headphones powered off press and hold the Multi-Function button (located next to the charging port on the bottom of the right ear cup)
for 5 seconds.
2.
You will hear a quiet tone and the indicator light will flash blue once, then flash red for 3 seconds then you will hear a louder repeating two note
tone and the indicator will repeatedly flash blue. Your headphones have now entered pairing mode.
3.
4.
Go into the Bluetooth settings/preferences of your music source and make sure your device is in discoverable mode.
In your music source’s Bluetooth preferences select “Samson RTE 2”
5. If your device asks for a passkey, enter digits 0000 (four zeros) and press OK.
4
English
Charging the battery
The RTE 2 headphones contains a battery capable of up to 14 hours
of usage. Although the headphones battery will come partially charged
from the factory, it is recommended to fully charge the battery before
using the headphones. To charge the battery, the headset has to be
connected with the included USB cable.
1. Connect the micro-USB plug into the USB port in the right side
of the headphones.
2. Plug the large end in the USB port of the computer or USB
5-volt adapter.
3. While the battery is charging, a constant green light will illumi-
nate on the right side of the headset. Once the battery is fully
charged, the green indicator light will turn off.
Note: When not in use, the battery will slowly self-discharge. If you
are planning not to use the headphones for a long period of time, it is
advised to partially discharge the unit and store in a cool place. Never
leave your headphones in a hot environment, especially exposed to the
sun.
RTE 2 Bluetooth® Headphones
5
Connecting with a Bluetooth device
In order to use your RTE 2 headphones with a Bluetooth device, you must first pair the devices
to create a wireless connection. The RTE 2 headphones will automatically connect to the
Bluetooth device as long as the headphones have not been paired to another device.
1. With the headphones powered off, press and hold the Multi-function button for 5 second.
A repeating two note audible sound will play and the indicator light will flash blue. The
headphones are now in pairing mode.
Note: While you are holding down the Multi-function button, the indicator will (1) flash
blue once, (2) flash red for three seconds, then (3) repeatedly flash blue.
2. In the settings of your Bluetooth device, set it to “discover” available devices.
3. From the Bluetooth device list, select the “Samson RTE 2” device.
4. If your device asks for a passkey, enter digits 0000 (four zeros) and press OK. Some
devices may also ask you to accept the connection.
5. When the connection is established, the indicator light will flash a blue light two times
every 5 seconds.
Note: To clear the pairing settings from the headset, turn off the headset. Then press and hold
the Multi-function button simultaneously with the down “–” volume button for 8 seconds. The
indicator light will flash red and blue three times to indicate the pairing has been cleared.
6
English
Connecting with an NFC Bluetooth device
Near Field Communication (NFC) is a protocol that allows you to connect your RTE 2
headphones to your Bluetooth device with NFC technology simply by touching the device
or bringing the device into close proximity.
1. Enable the NFC function on your Bluetooth device.
2. Gently touch your music device on the RTE 2’s NFC detection area (located on the
center of the left ear-cup).
3. Your music device should now recognize the signal from the headset.
Note: If the music device and the headset are pairing for the first time, you will need
to accept the pairing on the music device.
4. When the signal has been accepted on your music device, the headset will be paired
and ready for use.
RTE 2 Bluetooth® Headphones
7
Using the Optional Audio Cable
The headset has an auxiliary input located on the left ear cup. The auxiliary input can be used
to listen to music from most devices with a 3.5mm audio output. This allows the headphones to
work with devices without Bluetooth technology, if the headphone battery is not charged, or if
wireless connectivity is not available.
The headphones do not need to be powered on when using the auxiliary input. Simply plug the
cable into the 3.5mm input and your respective audio device.
Note: When the AUX cable is inserted, the Bluetooth function and the built-in microphone will
be disabled.
8
English
Controls and Indicators
Function
Control
Power On/Off
Play/Pause Music
Rewind
Press and hold the Multi-function button for 3 seconds.
Press the Play/Pause/Phone
button once.
Press and hold the left arrow button.
Press and hold the right arrow button.
Press the right arrow button once.
Fast-Forward
Next Track
Previous Track
Press the left arrow button once to go the beginning of the current track and twice two go to the
previous track.
Volume Up and Down Press the plus + button to raise the volume and the minus – button to lower the volume.
Function
Tones
Function
Indicator Status
Power On
Power off
Four ascending tones
Four descending tones
Pairing mode
Low Battery
Blue (blinking)
Red (flash once per minute)
Red (blinking)
Loss Connection Reminder Series of link loss tone
Standby (no connection)
Standby
Blue (flash slowly)
No connection
Series of link loss tone
Single short high tone
Single long mid tone
Clear/Reset Setting
Red and blue (flash three
times)
Answer/Cancel/End call
Reject/Transfer call
Min/Max volume
Battery low
Charging
Green (Off when fully charged)
Short high tone
3 note descending once a minute
RTE 2 Bluetooth® Headphones
9
Important Safety Information
1. Heed all warnings
2. Keep and follow all instructions.
3. The operating temperature range in user manual: from 0 degree Celsius to 45 degree Celsius. DO NOT use this apparatus near water
4. Clean only with dry cloth
5. DO NOT disassemble or replace the battery. If you suspect there is something wrong with the battery, please carry the unit to the service center
for help.
6. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE
INSTRUCTIONS
7. The battery should not be disposed together with other waste. The battery has to be disposed at an authorized place for recycling of electrical
and electronic appliances. By collecting and recycling waste, you help save natural resources, and make sure the product is disposed in an
environmental friendly and healthy way.
8. Unplug this apparatus during lightning storms or when unused for long periods of time
9. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat
10. Only use accessories specified by the manufacturer
11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
10
English
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can ra-
diate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION: To comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC Rules, this device is comply with Class B limits. All
peripherals must be shielded and grounded. Operation with non-certified peripherals or non-shielded cables may results in interference to radio or
reception.
MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the
device.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
EMC/RF requirements
EU Declaration of Conformity:
The equipment complies according to the Radio Equipment and Telecommunications Terminal Equipment Directive 1999/5/EC. This equipment
meets the following conformance standards:
Safety:
Health:
EMC:
EN 60065:2002/A12:2011
EN 62479: 2010
EN 301 489-1 V1.9.2
EN 301 489-17 V2.2.1
EN 55013: 2013
EN 55020:2007/A11:2011
EN 300 328 V1.8.1
Radio:
RTE 2 Bluetooth® Headphones
11
Copyright 2014
v3.1
Samson Technologies Corp.
45 Gilpin Avenue
Hauppauge, New York 11788-8816
Phone: 1-800-3-SAMSON (1-800-372-6766)
Fax: 631-784-2201
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Samson Technologies is
under license.
The aptX® mark and aptX logo are trade marks of CSR plc or one of its group companies and may be registered in one or more jurisdictions.
The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries.
|