OPERATOR'S MANUAL
15 in. (381 mm)
String Trimmer
RY41002 Series
EL15
(RY41002)
Your new trimmer has been engineered and manufactured to Ryobi’s high standard for dependability, ease of
operation and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual.
Thank you for buying a Ryobi trimmer.
SAVE THIS MANUAL FOR FUTURE REFERENCE
ꢀ
Use the right product. Use the product for the intended
ꢀ
ꢀ
Do not handle the product with wet hands.
Do not use the product if the switch does not turn the
product on or off. A product that cannot be controlled
with the switch is dangerous and must be repaired.
ꢀ
ꢀ
ꢀ
Avoid accidental starting; never carry the product with
your finger on the trigger.
Stay alert and pay attention to what you are doing. Use
common sense when using this product.
Do not force the product. It will do a better job with less
likelihoodofariskofinjurywhenyouoperateitattherate
for which it was designed.
ꢀ
ꢀ
Use the product for cutting grass and light weeds only.
Do not use for any other purpose.
ꢀ
Wearheavy, longpants, boots, andgloves. Donotwear
loose fitting clothing, short pants, or go barefoot. Do not
wear jewelry of any kind.
Before starting the product, position it so that the line
doesnotcomeincontactwithanythingyoudonotintend
to cut.
ꢀ
ꢀ
ꢀ
ꢀ
Secure hair above shoulder level to prevent entangle-
ment in moving parts.
ꢀ
ꢀ
Keep the grass deflector in place at all times while
operating the product. The product may overheat with-
out the grass deflector in place.
Do not allow children or untrained individuals to use this
product.
Keepallbystanders, children, andpetsatleast50ft. (15
m) away.
Stop the product immediately, unplug it, and check for
damage if you strike or become entangled with foreign
objects. Do not operate the product before having any
damage repaired.
Do not operate this product when you are tired, ill, or
under the influence of alcohol, drugs, or medication.
ꢀ
ꢀ
Do not operate in poor lighting.
ꢀ
ꢀ
Keep hands away from the cutting line. Do not attempt
to remove cut material or to hold material to be cut when
the line is moving. Be sure the unplug the product and
the release the trigger when clearing jammed material
from the line. Do not grasp the line when picking up or
holding the product.
Keep firm footing and balance. Do not overreach. Over-
reaching can result in loss of balance or exposure to hot
surfaces.
ꢀ
ꢀ
Keep all parts of your body away from moving parts.
Inspect the product before use. Replace any damaged
parts before use.
Be cautious after turning off the product. The line coasts
after turning off the product.
ꢀ
ꢀ
Never operate the product without the grass deflector in
place and in good condition.
Maintain a firm grip on both handles while trimming.
Keep the trimmer head below waist level. Never cut
withthetrimmerheadover30in. (76cm)ormoreabove
the ground.
GENERAL SAFETY RULES
WARNING:
purpose only.
When using electric gardening appliances, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock, and personal injury, includ-
ing the following:
READ ALL INSTRUCTIONS
GENERAL SAFETY RULES
ꢀ Clear the work area before each use. Remove all
objects, such as rocks, broken glass, nails, wire, or
string that can be thrown or become entangled in the
cutting line.
ꢀ Do not operate the product in damp or wet locations.
ꢀ Disconnect the product from the power supply when it is
not in use, before servicing, and when changing acces-
sories.
ꢀ Do not use the product in the rain.
ꢀ Wear safety glasses or goggles that are marked to
comply with ANSI Z87.1 standard when operating this
product.
SPECIFIC SAFETY RULES
SPECIFIC TRIMMER SAFETY RULES
ꢀ Replace the trimmer head if cracked, chipped, or dam-
aged in any way. Be sure the trimmer head is properly
installed and securely fastened.
ꢀ Make sure all guards, straps, deflectors, and handles
are properly and securely attached.
ꢀ Use only the manufacturer’s replacement line in the
trimmer head.
Page 3
ꢀ
Inspectextensioncordsfordeterioration,cuts,orcracks
ꢀ
ꢀ
ꢀ
Make sure the cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
ꢀ
A nameplate on the product indicates the unit’s voltage.
Never connect the product to an AC voltage that differs
from this voltage.
Donotabusethepowercord.Nevercarrytheproductby
the cord. Never yank the plug out of the receptacle.
Keep the cord away from heat, oil, and sharp edges.
To reduce the risk of electrical shock, use only round-
jacketed extension cords approved for outdoor use,
such as cords of type SW-A, SOW-A, STW-A, STOW-
A, SJOW-A, SJTW-W, or SJTOW-A. Since this tool is
double insulated, you may use a 2-wire extension cord
(an extension cord without a ground). However, you
mayalsousea3-wireextensioncord(anextensioncord
withaground)thathasaNEMA-typeconnector(parallel
blade, U ground). Extension cords are available from
your local retailer.
ꢀ
Maintain the product with care. Follow instructions for
changingaccessories. Keeptheproductdry, clean, and
free from oil and grease.
ꢀ
ꢀ
Release the trigger, allow the motor to stop, and unplug
the product before making adjustments or repairs.
Do not use the product if parts have been damaged.
Check the product to make sure that it will operate
properly and perform the intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, and any other condition that may
affect the unit’s operation. Inspect the unit’s power
connection. Any part that is damaged should be prop-
erly repaired or replaced by a Homelite authorized
service center.
ꢀ
Be sure to use a cord that is heavy enough to carry the
currentthatyourproductwilldraw. Thecorrectcordsize
depends on cord length and amperage rating (see
figures below). An undersized cord set will cause a drop
in line voltage resulting in loss of power and overheat-
ing. Use of an improper extension cord could result in a
risk of fire and electric shock. If an extension cord must
be used, make sure:
ꢀ
ꢀ
Keep the product clean of grass clippings and other
materials that may become lodged in the cutting lines.
Neverdouseorsquirttheproductwithwateroranyother
liquid. Keep handles dry, clean and free from debris.
After each use, clean with a soft, dry cloth.
ꢀ
Service on this product must be performed by qualified
repair personnel only. Service or maintenance per-
formed by unqualified personnel could result in injury to
the user or damage to the product. Such service may
also void your warranty.
ꢀ
Stop the motor when you are waiting to cut or when you
are walking from one cutting location to another.
ꢀ
GroundFaultCircuitInterrupter(GFCI)protectionshould
be provided on the circuits(s) or outlet(s) used for this
product. Receptacles with built-in GFCI protection are
available and may be used.
SPECIFIC SAFETY RULES
ELECTRICAL SAFETY RULES
in the insulation. Repair or replace the cords if any
defects appear.
MAINTENANCE RULES
a. That pins on plug of extension cord are the same
number, size and shape as those on the plug on the
charger.
SERVICE RULES
b. That the extension cord is properly wired and in good
electrical condition; and
c. That the wire size is large enough for the AC ampere
rating of the product as specified below:
Cord Length (Feet) 25'
Cord Size (AWG) 16
50'
14
100'
12
ꢀ Useonlyidenticalreplacementpartswhenservicingthe
product. Follow the instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow maintenance instructions may create a
riskofshock, seriousinjurytotheuser, ordamagetothe
product. Such use may also void your warranty.
Note: AWG = American Wire Gage
ꢀ To reduce the risk of electrical shock, this product has a
polarized plug (one blade is wider than the other) and
requires the use of a polarized extension cord. This
product’s plug fits into a polarized extension cord in only
one way. If the plug does not fit fully into the extension
cord, reverse the plug. If the plug still does not fit, obtain
a correct polarized extension cord. Use of a polarized
extension cord requires use of a polarized wall outlet.
This product’s plug fits into a polarized wall outlet in only
one way. If the plug does not fit fully into the wall outlet,
reverse the plug. If the plug still does not fit, contact a
qualified electrician to install the proper wall outlet. Do
not change the product plug, the extension cord recep-
tacle, or the extension cord plug in any way.
STORAGE AND TRANSPORTATION RULES
ꢀ Storetheproductinsideinadryplace. Storetheproduct
up high or lock it up to prevent unauthorized use or
damage. Keep the product out of the reach of children.
ꢀ Secure the product when transporting it.
ꢀ Save these instructions. Refer to them frequently
and use them to instruct others who may use this
product. If you loan someone this product, loan these
instructions also.
Page 4
SYMBOLS
Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the tool more safely and effectively.
SYMBOL
NAME
EXPLANATION
Safety Alert
Precautions that involve your safety.
.
Ricochet
Thrown objects can cause severe injury. Wear
protective clothing and boots.
Eye Protection
Always wear safety goggles or safety glasses with
side shields and a full face shield when operating
this product.
Keep Bystanders Away
No Blade
Keep all bystanders at least 50 ft. (15 m) away.
50' 15m
Do not install any type of blade on this product.
Class II Construction
Double-insulated construction.
Wet Conditions Alert
Do not expose to rain or use in damp locations.
Read Operator’s Manual
To reduce the risk of injury, user must read and
understand operator’s manual before using this
product.
Page 5
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will result in
death or serious injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in
serious injury.
CAUTION:
`
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
CAUTION: (Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When ser-
vicing, use only identical replacement parts.
To avoid serious personal injury, do not attempt to use
this product until you read thoroughly and understand
completely the operator’s manual. Save this operator’s
manual and review frequently for continuing safe op-
eration and instructing others who may use this prod-
uct.
WARNING:
Observe all normal safety precautions related to avoid-
ing electrical shock.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
Page 6
SPECIFICATIONS
MOTOR
Motor Type ......................................................................................................................................................... 120 V AC
Operating RPM ......................................................................................................................................................... 7500
Amperes................................................................................................................................................................ 6 amps
DRIVE SHAFT AND CUTTING HEAD
Drive Shaft ............................................................................................................................................. 1/4 in. Flex Shaft
Cutting Head ......................................................................................................................................Bump Line Release
Cutting Path Diameter.............................................................................................................................. 15 in. (381 mm)
Drive Shaft Housing ................................................................................................................................. Aluminum Tube
Cutting Line Diameter ................................................................................................................................080 in. (2 mm)
UNPACKING
INSTRUCTIONS
PACKING LIST
ꢀ
ꢀ
Carefully remove the parts from the box.
Upper shaft (Power head) (1)
Attachment shaft (Cutting head) (1)
Front Handle (1)
Inspectthepartscarefullytomakesurenobreakageor
damage occurred during shipping.
ꢀ
ꢀ
Do not discard the packing material until you have
carefullyinspectedandsatisfactorilyoperatedtheprod-
uct.
Carriage bolt - 6 mm x 50.0 mm (1)
Flat washer - 6 mm (1)
Wing nut - 6 mm (1)
If any parts are damaged or missing, please call
1-800-860-4050 for assistance.
Grass deflector (1)
Wing nut - 1/4 in. (1)
Flat washer - 1/4 in. (1)
Lock washer - 1/4 in. (1)
Hex bolt - 1/4 in. x 2 in. (1)
Operator’s manual
WARNING:
If any parts are missing, replace them before
operaing the product. Failure to do so could result in
serious personal injury.
Page 7
FEATURES
GRASS DEFLECTOR
TOP-MOUNTED MOTOR
The trimmer includes a grass deflector that helps protect
you from flying debris.
The top-mounted motor improves balance and is
located away from the dust and debris of the cutting
area.
ERGONOMIC DESIGN
The design of the trimmer provides for easy handling. It is
designed for comfort and ease of grasp when operating in
different positions and at different angles.
CORD RETAINER
The cord retainer helps prevent accidental unplugging
of the extension cord.
DUAL LINE
WARNING:
The dual line permits more efficient and aggressive
cutting.
Do not attempt to modify this product or create acces-
sories not recommended for use with this product.
Any such alteration or modification is misuse and
could result in a hazardous condition leading to seri-
ous personal injury.
EZ LINE™ TAP ADVANCE SYSTEM
The EZ Line™ Tap Advance System allows easy line
advance during trimmer operation.
MOTOR
HOUSING
TRIGGER
HANDLE
FRONT
HANDLE
TRIGGER
CORD
RETAINER
CORD
BEND
RELIEF
DUAL
LINE
GRASS
DEFLECTOR
Fig. 1
Page 8
ASSEMBLY
CONNECTING THE ATTACHMENT TO THE
UPPER SHAFT
See Figure 2.
COUPLER
The coupler connects the attachment to the upper shaft.
GUIDE
RECESS
Follow these steps to connect the attachment to the upper
shaft.
UPPER
SHAFT
ꢀ
ꢀ
ꢀ
Loosen the knob by turning it counterclockwise.
Remove the end cap from the attachment shaft.
BUTTON
Align the button with the guide recess on the upper
shaft.
POSITIONING
HOLE
ꢀ
ꢀ
Slide the attachment shaft into the upper shaft until the
attachment shaft clicks into place.
KNOB
ATTACHMENT
SHAFT
NOTE: If the button does not release completely in
the positioning hole, the shafts are not locked. Slightly
rotate the attachment shaft until the button is locked
into place.
Fig. 2
Tighten the locking knob securely by turning it clock-
wise.
NOTE: During operation, periodically check the knob
and tighten as necessary.
REMOVING THE ATTACHMENT FROM THE
UPPER SHAFT
See Figure 2.
FRONT
HANDLE
Disconnecttheuppershaftandattachmentshaftforstorage
or when a job calls for a different attachment.
BOLT
Follow these steps to remove the attachment from the
upper shaft.
ꢀ
Release the trigger and allow the trimmer to coast to a
stop.
ꢀ
ꢀ
Unplug the trimmer.
Loosen the locking knob by turning it counterclock-
wise.
WASHER
Fig. 3
ꢀ
Push the button, while pulling out the attachment.
WING NUT
ATTACHING THE FRONT HANDLE
See Figure 3.
Follow these steps to attach the front handle.
ꢀ
Press the front handle onto the upper shaft so that the
handle is angled toward the trigger handle.
ꢀ
Place the front handle along the upper shaft to a
position that allows for comfortable operation.
ꢀ
ꢀ
ꢀ
Slide the bolt through the holes in the front handle.
Slide the washer onto the bolt.
Placethewingnutontotheboltandtightenthewingnut
securely.
Page 9
ꢀ
An extension cord retainer is located on the bottom
of the trimmer. This provides strain relief for the cord,
preventing unwanted disconnects.
ꢀ
Use the extension cord retainer when you connect
the extension cord to the power cord to prevent
disconnection. Use only an outdoor approved
extension cord as indicated by the letters “W-A” on
the cord’s jacket.
ASSEMBLY
ATTACHING THE GRASS DEFLECTOR
See Figure 4.
WING
NUT
GRASS
DEFLECTOR
WASHER
WARNING:
The line cutting blade on the grass deflector is sharp.
Avoid contact with the blade. Failure to avoid contact
can result in serious personal injury.
Follow these steps to attach the grass deflector.
LOCK
WASHER
ꢀ
Slide the grass deflector onto the attachment shaft
and fit it over the bracket.
ꢀ
Install the bolt through the holes in the tabs on the
grass deflector and the slots in the bracket on the
attachment shaft.
BOLT
CUT OFF
BLADE
ꢀ
Install the flat washer, the lock washer, and the wing
nut.
ꢀ
ꢀ
Tighten the wing nut securely.
Remove the protective packaging from the line cutting
blade.
Fig. 4
EXTENSION CORD RETAINER
Note: To reduce the disconnection of the power cord
from the extension cord during operation, use the
extension cord retainer described below.
METHOD OF SECURING EXTENSION CORD
Fig. 5
ꢀ
Loop the extension cord through the extension
cord retainer slot located on the bottom end of
the trimmer. See Figure 5.
ꢀ
ꢀ
Pull loop of extension cord around tongue and
pull tight. See Figure 6.
Attach extension cord to plug on trimmer.
See Figure 6.
CORD
RETAINER
Fig. 6
Page 10
OPERATION
WARNING:
The product may throw objects during operation, caus-
ing injury to the operator or to bystanders. Always
wear suitable eye protection, boots, gloves, and long,
heavy pants while operating the product.
STARTING AND STOPPING THE TRIMMER
See Figure 7.
ꢀ
ꢀ
To start the trimmer: Press the trigger.
To stop the trimmer: Release the trigger.
OPERATING THE TRIMMER
See Figure 8.
Follow these steps to operate the trimmer.
TRIGGER
ꢀ
ꢀ
Plug the trimmer cord into an extension cord approved
for outdoor use. Refer to “Electrical Safety Rules ”
earlier in this manual.
Fig.7
Hold the trimmer with your right hand on the trigger
handle and your left hand on the front handle.
NOTE: Keep a firm grip with both hands during opera-
tion.
ꢀ
Placethetrimmerontherightsideofyourbodywiththe
engine behind and away from your body.
ꢀ
ꢀ
Press the trigger to start the trimmer.
Trim grass and weeds in a right-to-left motion with the
line parallel to the ground.
CUTTING TIPS
ꢀ
Inspect and clear the area to be trimmed for any rocks,
broken glass, or wire that could be thrown or become
entangled in the cutting line.
ꢀ
ꢀ
ꢀ
Trim only when grass or weeds are dry.
Keep the cutting line parallel to the ground.
Cut grass or weeds over eight inches tall from the top
to the bottom in small amounts. This will prevent grass
becoming wrapped around the trimmer head assem-
bly, which may result in damage due to overheating. If
grass becomes wrapped around the trimmer head
assembly, stop the trimmer, unplug it, and remove the
grass.
ꢀ
Move the trimmer slowly in and out of the area you are
cutting, keeping the trimmer at the desired cutting
height.
Fig. 8
ꢀ
ꢀ
Use the tip of the line to do the cutting. Do not force the
trimmer head assembly into uncut grass.
Feed out some line after each use to prevent the line
from retracting into the cutting head.
Page 11
OPERATION
ꢀ
The tip of the cutting line will wear during use; this
reduces the cutting swath. If the line is not advanced
occasionally, it will wear down to the eyelet. When the
trimmer stops, the line tends to relax and may retract
into the trimmer head assembly. Should this occur,
unplug the trimmer, remove the spool, refeed the line
through the eyelets, and reassemble the spool.
ꢀ
ꢀ
Avoid hitting objects with the line, such as chain-link
fences or concrete, as this causes rapid wear.
RETAINING
CAP
Never drag the trimmer head assembly on the ground
while trimming.
ADVANCINGTHECUTTINGLINEAUTOMATI-
CALLY
See Figure 9.
The trimmer includes the EZ Line™ Tap Advance System.
Followthesestepstoadvancethecuttinglineautomatically.
Fig. 9
ꢀ
ꢀ
Press the trigger.
Tap the retaining cap lightly on the ground while the
motor is running. Do not hold the retaining cap on the
ground.
LINE
NOTE: The line cutting blade on the grass deflector
will cut the line to the proper length.
NOTE: To help prevent line tangle, tap only once to
lengthen the line. If additional line is required, wait a
few seconds before retapping the retaining cap. Keep
the line length at or near full cutting diameter.
RETAINING
CAP
ADVANCING THE CUTTING LINE MANUALLY
See Figure 10.
If the cutting line wears to less than the recommended
length, you may not be able to lengthen it by tapping the
retaining cap.
Fig. 10
Follow these steps to advance the cutting line manually.
ꢀ
Release the trigger and allow the trimmer to coast to a
stop.
ꢀ
ꢀ
Unplug the trimmer.
Pull sharply on the line while pushing down on the
retaining cap.
Page 12
OPERATION
CUT OFF BLADE
This trimmer is equipped with a cut-off blade on the grass
deflector. For best cutting, advance string until it is trimmed
to length by the cut-off blade. Advance string whenever
you hear the engine running faster than normal. This will
maintain best performance and keep string long enough
to advance properly.
DIRECTION OF
ROTATION
CUTTING TIPS
See Figure 11.
ꢀ
Keep the trimmer tilted toward the area being cut; this
is the best cutting area.
ꢀ
ꢀ
Do not cut in dangerous cutting area.
Use the tip of string to do the cutting; do not force string
head into uncut grass.
ꢀ
ꢀ
Wire and picket fences cause extra string wear, even
breakage. Stone and brick walls, curbs, and wood may
wear string rapidly.
DANGEROUS CUTTING
AREA
BEST CUTTING
AREA
Avoid trees and shrubs. Tree bark, wood moldings,
siding, and fence posts can easily be damaged by the
string.
Fig. 11
GRASS DEFLECTOR LINE TRIMMING CUT-
OFF BLADE
See Figure 12.
This trimmer is equipped with a line trimming cut-off blade
on the grass deflector. For best cutting, advance string
until it is trimmed to length by the cut-off blade. Advance
string whenever you hear the engine running faster than
normal. This will maintain best performance and keep
string long enough to advance properly.
CUT-OFF
BLADE
Fig. 12
Page 13
MAINTENANCE
WARNING:
Use only identical Ryobi replacement parts when ser-
vicing this product. Use of any other parts may create
a hazard or cause product damage.
CLEANING THE TRIMMER
Release the trigger, allow the trimmer to coast to a stop,
and unplug the trimmer before cleaning.
ꢀ
ꢀ
Clean the exterior of the trimmer with a soft, dry cloth.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types
of commercial solvents and may be damaged by their
use.
Fig. 13
ꢀ
ꢀ
Wipe or scrape the trimmer head and spool area when
they accumulate dirt or clippings.
Scrape or brush debris away from air intake vents on
the motor housing.
SERVICING THE TRIMMER
ꢀ
Check all fasteners and tighten as necessary. If any
part is damaged or lost, repair it or replace it.
ꢀ
Any other service should be performed at a Homelite
Authorized Service Dealer.
UPPER AREA
REPLACING THE CUTTING LINE
See Figures 13, 13a and 13b.
WARNING:
Use of line other than the original .080 in. monofila-
ment cutting line could cause serious personal injury
or damage to the trimmer.
Follow these steps to replace the cutting line.
ꢀ
Release the trigger and allow the trimmer to coast to a
stop.
LOWER AREA
Fig. 13a
ꢀ
Unplug the trimmer.
TRIMMER
HEAD
WARNING:
Make sure the trimmer head stops rotating when you
release the trigger. Contact with a rotating trimmer
head could cause personal injury.
SPOOL
ꢀ
Remove the retaining cap by turning it counterclock-
wise.
ꢀ
ꢀ
Remove the empty spool.
Clean the trimmer head thoroughly. Inspect the trim-
mer head for any damaged or worn parts.
ꢀ
ꢀ
Cut two pieces of line approximately 9 ft. (2.7 m) long.
Insert the end of the new line into the hole in the upper
threaded area of the spool.
RETAINING
CAP
Fig. 13b
Page 14
MAINTENANCE
ꢀ
Wind the line counterclockwise around the spool fol-
lowing arrows on spool. Do not overfill.
DRIVE
SHAFT
NOTE: After winding the line, there should be about 6
in. (152 mm) between the wound line and the outside
edge of the spool.
TRIMMER
HEAD
ꢀ
ꢀ
Secure the line temporarily by pushing it into one of the
slotted tabs on the spool.
Repeat the process for the lower threaded area of the
spool, winding the line clockwise and securing it in the
slotted tab opposite the first secured line.
ꢀ
ꢀ
Insert the lines into the eyelets in the trimmer head.
Place the spool on the drive shaft.
SPOOL
NOTE: To install the spool, you may need to rotate it
slightly.
NOTE: If the line should tangle or break at the eye-
lets, remove the spool, refeed the line through the eye-
lets, and reassemble the spool on the trimmer.
Fig. 14
ꢀ
ꢀ
ꢀ
ꢀ
Release the lines from the tabs by sharply pulling each
line while pushing down on the spool.
ꢀ
Hold the spool so that its tabbed side is positioned
upward.
Push down on the spool to reveal the threads on the
drive shaft.
NOTE: On the new spool, the ends of the lines are
secured in slots on tabs. Release the line from the
tabs, unwind approximately six inches of line, and re-
secure the lines in the tabs.
Place the retaining cap on the threads inside the drive
shaft.
Secure the retaining cap by turning it clockwise.
ꢀ
ꢀ
Insert the lines on the new spool into the eyelets in the
trimmer head.
Place the spool on the drive shaft.
WARNING:
NOTE: To install the spool, you may need to rotate it
slightly.
An improperly installed retaining cap or spool could
fly off the trimmer. Contact with a thrown retaining
cap or spool could cause personal injury.
NOTE: If the line should tangle or break at the eye-
lets, remove the spool, refeed the line through the eye-
lets, and reassemble the spool on the trimmer.
REPLACING THE SPOOL
See Figure 14.
ꢀ
Release the lines from the tabs by sharply pulling each
line while pushing down on the spool.
The spool may wear during normal use of the line advance
feature and may require occasional replacement.
Replacement spools are available through your local
retailer.
ꢀ
ꢀ
ꢀ
Push down on the spool to reveal the drive shaft.
Place the retaining cap on the drive shaft.
Secure the retaining cap by turning it clockwise.
ꢀ
ꢀ
Release the trigger.
Unplug the trimmer.
WARNING:
Make sure the trimmer head stops rotating. Contact
with a rotating trimmer head could cause personal
injury.
ꢀ
Remove the retaining cap by turning it counterclock-
wise.
ꢀ
ꢀ
Remove the empty spool.
Clean the trimmer head thoroughly. Inspect the trim-
mer head for any damaged or worn parts.
Page 15
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
SOLUTION
Line will not advance when tap
retaining cap
1. Lubricate with a silicone spray.
2. Install more line (Refer to “Replacing the
Cutting Line” earlier in this manual).
3. Pull lines while alternately pressing down on
and releasing spool retainer.
1. Line is welded to itself.
2. Not enough line on spool.
3. Line is worn too short.
4. Line is tangled on spool.
4. Remove line from spool and rewind (Refer to
“Replacing the Cutting Line” earlier in this
manual).
Retaining cap is hard to turn
Screw threads are dirty or dam-
aged.
Clean threads and lubricate with grease. If no
improvement, replace spool retainer.
Cut tall grass from the top down.
Cutting tall grass at ground level.
Grass wraps around the
attachment shaft and the
trimmer head assembly
Page 16
ACCESSORIES
REPLACEMENT PARTS
String Head (RH Thread) .080 in. (2 mm) ......................................................................................................... DA03001A
Spool & Line .080 in. (2 mm) ..............................................................................................................................UP00145
String Refill .080 in. (2 mm); 390 ft. (118 mm)......................................................................................................D06511
String Refill .080 in. (2 mm); 50 ft. (15 mm)........................................................................................................D06509A
Retaining Cap (RH thread)............................................................................................................................... DA98866A
Retaining Cap (Power Care™) ...........................................................................................................................AP04106
OPTIONAL ATTACHMENTS
Expand-It Tiller Attachment..............................................................................................................................UT15550A
Expand-It Edger Attachment........................................................................................................................... UT15518E
Expand-It Straight Shaft Trimmer Attachment.................................................................................................UT15522E
UT15550A
UT15522E
UT15518E
WARNING:
The use of attachments or accessories not listed above could result in serious personal injury.
Page 17
OPERATOR'S MANUAL
15 in. (381 mm)
String Trimmer
RY41002 Series
• SERVICE
Now that you have purchased your product, should a need ever exist for
repair parts or service, simply contact your nearest Authorized Service
Center. Be sur to provide all pertinent facts when you call or visit. Please call
1-800-860-4050 for your nearest Authorized Service Center.
•
MODEL NO. AND SERIAL NO.
Themodelnumberofthistoolisfoundonaplateattachedtothemotorhousing.
Please record the serial number in the space provided below.
•
HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
• Model No. RY41002 (EL15)
• Serial No.
RYOBI TECHNOLOGIES INC.
1428 Pearman Dairy Road
Post Office Box 1207
Anderson, SC 29625
Anderson, SC 29622
Phone 1-800-860-4050
983000-388
9-04
|