OPERATOR'S MANUAL
WIDE TABLE KIT
4730301
FOR USE WITH RYOBI BT3100 AND
RYOBI BT3100-1 TABLE SAW
WIDE TABLE KIT SHOWN
ATTACHED TO BT3100/BT3100-1
TABLE SAW
LUMBER NOT INCLUDED WITH THIS KIT
TABLE SAW AND STAND NOT INCLUDED WITH THIS KIT
Your new Wide Table Kit has been engineered and manufactured to Ryobi's high standard for dependability, ease
of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this
product.
Thank you for buying a Ryobi accessory kit.
SAVE THIS MANUAL FOR FUTURE REFERENCE
SYMBOLS
The purpose of safety symbols is to attract your attention to possible dangers.The safety symbols, and the explanations
with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any
danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
SYMBOL MEANING
DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious
injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or seri-
ous injury.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moder-
ate injury. It may also be used to alert against unsafe practices that may cause property damage.
Note:
Advises you of additional information concerning the operation or maintenance of the equipment.
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance, and repair information.
SYMBOL
NAME
MEANING
Wet Condition Alert
• Do not expose to rain or use in damp locations.
• Failure to keep your hands away from the blade
will result in serious personal injury.
No Hands Symbol
• To reduce the risk of injury, the user must read and
understand the operator’s manual before using this product.
Read the Operator’s Manual
Eye Protection
• Always wear safety goggles or safety glasses with side
shields and a full face shield when operating this product.
SAVE THESE INSTRUCTIONS
UNPACKING
Your new Wide Table Kit includes two 41 in. extension rails,
plusthenecessarybracketsandconnectinghardwarerequired
to make one wide support base and a rear extension table
for your BT3100/BT3100-1 table saw. All you have to supply
is the lumber required for table tops and table legs, plus the
wood screws, nails, bolts, etc. required to secure the table
legs to the table top.
Inspect all parts carefully to make sure no breakage or
damage occured during shipping.
If any parts are damaged or missing, please call 1-800-
525-2579 for assistance.
WARNING:
If any parts are missing do not assemble the kit until the
missing parts are replaced. Failure to do so could result
in serious personal injury
Remove the parts from the box. Make sure that all items
listed in the loose parts list are included.
3
LOOSE PARTS
Table Bracket.....................................................................8
Hex Bolt (5/16-18 x 1/2 in)...............................................10
Wood Screw (#10 x 5/8 in. Rd. Hd.) ................................16
Washer (1/4 in.).................................................................4
Rear Extension Rail...........................................................1
Hex Bolt (5/16-18 x 5/8 in.)................................................2
Spacer...............................................................................2
Connector..........................................................................4
Front Extension Rail..........................................................1
Square Head Bolt (1/4-20 x 1/2 in.)...................................4
Hex Nut (1/4-20)................................................................4
T-Nut................................................................................12
Washer (5/16 in.).............................................................12
T-NUT
HEX BOLT
SQUARE HEAD BOLT
WASHER
HEX NUT
HEX BOLT
WASHER
FRONT
EXTENSION RAIL
REAR
EXTENSION RAIL
SPACER
CONNECTOR
TABLE
BRACKET
WOOD SCREW
Fig. 1
TOOLS NEEDED
1/2 IN. SOCKET
#2 PHILLIPS SCREWDRIVER
4
ASSEMBLY
TO ATTACH FRONT EXTENSION RAIL
FRONT
EXTENSION RAIL
See Figure 2 and 4.
Remove end caps from right end of front rail on your
BT3100/BT3100-1 table saw. See Figure 4.
Slide one of the T-nuts into bottom channel of front rail on
your saw. Slide a second T-nut into back channel of front
rail.
Attach one of the connectors provided to T-nut on bottom
of front rail and secure with a washer (5/16 in.) and a hex
bolt (5/16-18-x 1/2 in.). Finger tighten only.
HEX BOLT
T-NUT
Orient front extension rail so that it matches front rail of
your saw. Place two T-nuts in matching channels of front
extension rail.
CONNECTOR
Connect bottomT-nut to connector on front rail of your saw
and secure with a washer (5/16 in.) and a hex bolt (5/16
in. x 1/2 in.). Finger tighten only.
WASHER
TABLE BRACKET
Attachasecondconnectortobackchanneloffrontrailand
front extension rail. Secure it to each T-nut with a washer
(5/16 in.) and hex bolt (5/16 in. x 1/2 in.). Finger tighten
only.
TO ATTACH REAR EXTENSION RAIL
See Figure 3 and 5.
FRONT RAILS
SHOWN ATTACHED
Fig. 2
The rear extension rail attaches to rear rail on your BT3100/
BT3100-1 table saw by repeating the above procedure for
attaching front extension rail. The only difference being the
rear rail has a different configuration. See Figure 3.
REAR
EXTENSION RAIL
NOTE: There are several repetitive steps required for
assembling this kit. Please study and review illustrations
closely for clarification when asked to repeat a procedure.
After attaching rear rail extension to your saw you should now
have the front and rear extension rails attached to your saw
using four connectors, eight T-nuts, eight washers (5/16 in.),
and eight hex bolts (5/16 in. x 1/2 in.).
T-NUT
CONNECTOR
WASHER
HEX BOLT
TABLE BRACKET
Using a 1/2 in. socket or the small wrench supplied with your
table saw, tighten all eight bolts securely. Assure the two rail
sets are straight before, during and after tightening.
SPACER
REAR RAILS SHOWN
ATTACHED
Fig. 3
5
ASSEMBLY
TO ATTACH TABLE BRACKETS
Slide two T-nuts into channel on rear portion of front
FRONT
EXTENSION RAIL
extension rail. See Figures 2 and 4.
Attach two table brackets and secure with washers (5/16
in.) and hex bolts (5/16 in.x 1/2 in.) supplied. Hand tighten
only.
TABLE
BRACKET
Slide two T-nuts into channel on front portion of rear
extension rail. See Figures 3 and 5.
HEX BOLT
WASHER
T-NUT
Place a spacer between table brackets andT-nuts on rear
END CAP
SPACER
extension rail as shown in figure 5.
Fig. 4
Securetablebracketsandspacerswithtwowashers(5/16
in.) and two hex bolts (5/16 in. x 5/8 in.) supplied. Hand
tighten only.
REAR
EXTENSION RAIL
NOTE: These bolts are longer to accomodate spacers.
Spacers are needed to provide clearance for the rip fence
when sliding along extension rails.
AUXILIARY TABLE TOP (not supplied)
We suggest you make the auxiliary table top from a piece
of plywood cut 22 in. wide by 44 in. long by 3/4 in. thick.
TABLE
BRACKET
Space table brackets on each of the four corners so that
they are approximately 6 in. from the ends of extension
rails. See Figures 4 and 5.
WASHER
T-NUT
END CAP
HEX BOLT
Place table top in desired position on table brackets and
Fig. 5
adjust table brackets as needed.
NOTE: End of table top closest to saw will rest on lip of
accessory table. See Figure 6.
ACCESSORY
TABLE
AUXILIARY TABLE TOP
(22 in. X 44 in. X 3/4 in.)
Tighten the four table bracket bolts securely.
Slide rip fence the entire length of extension rails to
make sure it will clear your new extension table. Make
adjustmentsasneededforclearanceandsmoothoperation
of rip fence.
Cut a piece of 2 x 4 approximately 19 in. long and secure
to bottom of table top with wood screws. See Figure 8.
NOTE: Useflatheadwoodscrews(notincluded)ifattaching
this piece thru table top. Make sure these screw heads
are below the surface of table top. We suggest you mount
it from underneath table top if possible.
LIP
Fig. 6
This piece should also be located close to the end of your
table top. We suggest that you turn it on its edge as shown
in figure 8.
NOTE: Table legs will be secured to this piece of wood.
AUXILIARY
TABLE TOP
Reposition table top on table brackets and secure with
wood screws (#10 x 5/8 in.) provided. See Figure 7.
TABLE
BRACKET
NOTE: These screws mount from underneath table top.
WOOD
SCREW
Fig. 7
6
ASSEMBLY
TABLE LEGS (not supplied)
See Figure 8.
AUXILIARY
TABLE TOP
Table legs can be made from either 2 x 4s or by purchasing
a Ryobi Leg Set, #4730305, depending upon the application
in which your saw is being used. For example, if your saw is
being used in a permanent application you may want to use
2 x 4s which will be more sturdy and provide extra stability.
The metal leg set may be preferable for portable applications
or when moving your saw around in a workshop.
19 in. 2 X 4
TABLE LEGS MADE FROM 2 X 4s
Option #1
Cut two 2 x 4 legs the exact length required to support
TABLE
LEG
extension table.
Make sure ends are cut perfectly square for better
WOOD SCREWS
(NOT INCLUDED)
stability.
Place legs flush against bottom of table top and against
19 in. 2 x 4 attached to bottom of table top. See Figure 8.
TABLE LEG OPTION # 1
Secure table legs to table top with wood screws or bolts,
washers, and hex nuts (not included).
TABLE LEG OPTION # 2
TABLE LEG OPTION # 3
If extra bracing is needed, cut a scrap piece of wood and
attach to bottom of table legs. See Figure 9.
Option #2
Option #2 will allow table legs to be adjusted to the proper
height when your saw is used in portable applications, or in
situations where the floor is not perfectly level. This option
requires cutting a slot in top of table legs as shown in figure 8.
ADDITIONAL TABLE LEG OPTIONS
Additional options are also available for making table legs:
Option #3
Fig. 8
If desired, table brackets can also be used for leg brackets.
This option would eliminate the necessity of cutting slots in
top of table legs for height adjustments.
NOTE: Additional table brackets are available and may
also be purchased. Table brackets can be mounted upside
down on table legs and secured to extension rails. Using
the appropriate bolts, washers, and T-nuts will permit slots in
tablebracketstothenbeusedformakingheightadjustments.
See Figure 8.
Option #4
Itisalsopossibletoturnlegs90°fromthewaywehaveshown
and attach to each end of the 19 in. 2 x 4 under table top.
This option attaches similar to the way we have described
above, however, because of very close dimensions, it is a
more difficult procedure.
OPTIONAL BRACE
TABLE LEGS SHOWN
ATTACHED TO AUXILIARY TABLE TOP
Fig. 9
7
ASSEMBLY
This kit also includes brackets and connecting hardware for
REAR
EXTENSION RAIL
makinganextensiontablebehindthebladetoprovidesupport
and control when ripping large panels. The size of this table
should be made according to application requirements and
individual preferences.
TABLE
BRACKET
TO ATTACH TABLE BRACKETS
See Figure 10.
Insert the (four) square head bolts (1/4-20 x 1/2 in.) into
slot in back of rear rail of your table saw and rear extension
rail.
Space bolts along rails as needed to accomodate rear
extension table.
WASHER
HEX NUT
Attach remaining four table brackets to rails and secure
SQUARE HEAD BOLT
with washers (1/4 in.) and hex nuts (1/4 in.) provided.
Hand tighten hex nuts.
REAR EXTENSION TABLE TOP (not supplied)
See Figure 11.
Fig. 10
REAR
EXTENSION
TABLE
We suggest you cut a piece of plywood 82 in. long by 3/4
in. thick. As previously mentioned the width should be
determined according to application requirements and
individualpreferences. Twoslotsshouldbecutintheplywood
as shown in figure 11. These slots will permit sliding miter
table to continue to be used as it was designed. Slots must
be cut large enough to permit full travel of sliding miter table,
so as not to lose its versatility.
SLIDING MITER TABLE
AUXILIARY
EXTENSION
TABLE
Place rear extension table top in desired position on table
brackets and adjust table brackets as needed.
Tighten the (four) hex nuts securely.
Secure rear extension table top with wood screws (#10 x
5/8 in.) provided. See Figure 8.
NOTE: Thesescrewsmountfromunderneathtabletopthe
same way auxiliary table top mounts to table brackets.
TABLE LEGS (not supplied)
See Figure 8.
OPTIONAL
BRACE
OPTIONAL BRACE
Table legs (four) for the rear extension table should be
constructed. Construct them similar to methods explained
for making table legs for auxiliary extension table. Either
2 x 4s or Ryobi Leg Set, # 4730305 can be used.
TABLE SAW SHOWN WITH
THE AUXILIARY EXTENSION TABLE AND
THE REAR EXTENSION TABLE
A piece of 2 x 4 for securing table legs would need to be
mounted on bottom of rear extension table. It should be
located close to the end of rear extension table.
Fig. 11
If extra bracing is needed, cut pieces of scrap wood and
attach to bottom of table legs. See Figure 11.
8
RYOBI WIDE TABLE KIT NO. 4730301
Now that you have purchased your Wide Table Kit, should a need ever exist for repair parts or service,
simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when
you call or visit.
PARTS LIST
Key
No.
Part
Description
Number
Qty.
1
2
3
4
5
6
7
8
0181010812
615570-014
706382-361
970147-002
969251-001
970146-002
615570-008
661847-002
0181011805
969969-001
623166-005
706382-358
622171-053
972000-219
Front Extension Rail..............................................................................................1
* Hex Bolt (5/16-18 x 1/2 in.) .................................................................................10
* Washer (5/16 in.) ................................................................................................12
Connector .............................................................................................................4
T-Nut ...................................................................................................................12
Table Bracket ........................................................................................................8
* Hex Bolt (5/16-18 x 5/8 in.) ...................................................................................2
Spacer ..................................................................................................................2
Rear Extension Rail..............................................................................................1
* Wood Screw (#10 x 5/8 in. Rd. Hd.)....................................................................16
* Bolt (1/4-20 x 1/2 in. Sq. Hd.)................................................................................4
* Washer (1/4 in.) ....................................................................................................4
* Hex Nut (1/4-20) ..................................................................................................4
Operator's Manual (not shown)
9
10
11
12
13
* STANDARD HARDWARE ITEM — MAY BE PURCHASED LOCALLY
9
OPERATOR'S MANUAL
WIDE TABLE KIT
4730301
FOR USE WITH RYOBI BT3100 AND
RYOBI BT3100-1 TABLE SAW
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or service,
simplycontactyournearestRyobiAuthorizedServiceCenter.Besuretoprovideallpertinent
facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi Authorized
of Authorized Service Centers.
• HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS,
ALWAYS GIVE THE FOLLOWING INFORMATION:
4730301
• MODEL NUMBER
• SERIAL NUMBER
RYOBI TECHNOLOGIES, INC.
1428 Pearman Dairy Road Anderson, SC 29625
Post Office Box 1207, Anderson, SC 29622-1207
Phone 1-800-525-2579
983000-389
10-03
|