READ CAREFULLY BEFORE USING AND THEN KEEP IN A SAFE PLACE.
ENGLISH
You have just purchased a fan heater, ideal for quickly heating the different rooms in your house.
This highly compact appliance can be easily stored or moved around from one room to another for your comfort.
3 - OPERATION
WIRING INSTRUCTIONS - FOR U.K. ONLY.
SAFETY NOTES - FOR REWIREABLE OR HOULDED PLUG.
The mains lead of this appliance may be already fitted with a BS 1363 13 A plug.
Should the fuse need to be replaced, a 13 A ASTA approved BS 1362 fuse must be used.
If your socket outlet is not suitable for the plug, then the plug must be removed (cut off if it is a moul-
ded on plug) and a appropriate one fitted. Warning : dispose of a plug that has been cut from the
power supply cord, as such a plug is hazardous if inserted in a live 13 A socket outlet elsewhere in
the house.
Always replace the fuse cover after fitting a fuse. The plug must NOT be used if the cover is omitted
or lost until a replacement is obtained - make certain that only the correct fuse cover is used and
fitted.
Starting up the appliance and choosing the operating mode:
Power selection : mod. HA 260 - HA 280
ECO
̈
̈
position : this position delivers power of 1000 W.
•
position : this position constantly delivers power of 2000 W.
For plugs with a detachable fuse cover the replacement must be thesame as the colour insert in the
base of the plug, or as directly by the embossed wording on the base of the plug.
If the detachable fuse cover is lost, a replacement may be purchased from Rowenta Service Centre
(see enclosed Service Information leaflet). Information for supply may also be obtained from the plug
manufacturer.
Mod. HA 270
Your appliance operates at 2000 W as soon as it is plugged into the mains
supply, if the thermostat is tripped.
U.K. ONLY - FITTING A PLUG.
Important : The wires in the mains cord are coloured in accordance with the following code Blue,
Neutral, Brown, live.
Please read the instructions given below before connecting the cord to a plug. If in doubt, please
consult a qualified electrician.
Heating light : Power LED :
This LED (D) comes on as soon as your appliance is powered up.
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows :
• the wire which is coloured BLUE must be connected to the terminal which is marked with the letter
“N” or coloured BLACK ;
• the wire which is coloured BROWN must be connected to the terminal which is marked with the let-
ter “L” or coloured RED.
Thermostat : mod. HA 260 - HA 280
Adjust the temperature setting, according
to your own comfort, by turning
button (A) (fig. 2-3) :
min.
max.
Brown
Neither core is to be connected to the earth terminal of a
three-pin plug.
This appliance requires a 13 A fuse ASTA approved to BS 1362.
or red
L
Fit correct
fuse
Blue or
black
Frost-free setting :
: mod. HA 270 - HA 280
N
Use cable
gripper
This setting enables you to automatically maintain the temperature above 0°C
in a normally insulated room, whose volume corresponds to the power of your
appliance.
To do this, plug in your appliance and turn button (A) so that the marker is
opposite the “ “ .
WARNINGS
It is essential that you read these instructions carefully and comply with the
following recommendations.
Cold ventilation setting :
: (mod. HA 260 - HA 280)
This appliance complies with European directives 73/23/EEC and
89/336/EEC.
This setting enables you to use your fan heater as a fan in summer.
Before using, always check the condition of the appliance, the power
socket and the power lead.
Do not pull on the power cable or the appliance, even to unplug it from
the wall socket.
USE OF THE APPLIANCE IN MOBILE MODE
In application of the new regulations concerning product stability, the sta-
bilizing ring (I) must be fixed under the base of the appliance and faste-
ned in the two holes using the 2 screws supplied (J).
Fully unwind the lead each time before use.
If the appliance is fixed to the wall, the socked must be accessible.
Do not place the appliance just below a power socket.
Never insert objects into the appliance (e.g. needles...).
When in use, this appliance must be kept out of the reach of young chil-
dren, animals and certain handicapped people.
Do not use your appliance in a dusty room or a room where there is a
risk of fire.
4 - INSTALLATION ON WALL
Your appliance can be bolted to the wall. It must be positioned vertically,
respecting the minimum distances (fig. 4).
To bolt your appliance to the wall, use 3 appropriate screws and 3 wall-
plugs.
This appliance is intended for domestic use only. It must therefore not be
used in industrial applications.
Start with the upper hole (G) located above the handle (E) (fig. 5).
The warranty will be void in the event of damage arising from improper
use.
If the power cable is damaged, it must be replaced by the manufacturer,
its after-sales service or a person with similar qualifications to avoid any
danger.
Drill a hole in the wall at the required height, insert a wall-plug and a screw.
Hang your appliance on the wall and lock it in a vertical position using the
holes (G) located on the appliance stand.
5 - CLEANING
VERY IMPORTANT :
Your appliance must be unplugged before proceeding with any cleaning
work.
You can clean it with a slightly damp cloth.
IMPORTANT: Never use abrasive products which might damage the appea-
rance of your appliance.
NEVER COVER THE APPLIANCE, even temporarily, as there is a danger of
overheating.
Keep the appliance 30 cm away from any objects (curtains, walls, aerosols,
etc.)
NEVER USE IT TILTED OR LYING ON ITS SIDE.
This appliance must not be used in damp places.
Do not use this appliance near a bath, shower, sink or swimming pool.
NEVER ALLOW WATER TO PENETRATE THE APPLIANCE.
Do not touch the appliance with wet hands.
We recommend that you clean the air inlet and outlet grills at least once a
year; (clean with a vacuum cleaner if necessary).
In the event of
a
long absence: turn the button (B) to the initial
6 - STORAGE
setting G (mod HA 260 - HA 280) and unplug the appliance or turn the button
(A) to the initial setting
(mod. HA 270) and unplug the appliance.
When storing your appliance, you can wind the lead around the stand and
clip the end into the lead clip (H).
It is important to allow the appliance to cool before winding the lead.
When you are not using your appliance, store it in a dry place.
1 - VOLTAGE
Before using the appliance for the first time, ensure that your mains voltage cor-
responds to the voltage indicated on the appliance.
Your appliance can be used with a power plug without an earth connection. It is a
7 - IN THE EVENT OF PROBLEMS
class II appliance (dual electrical insulation
).
Never dismantle your appliance yourself. A poorly repaired appliance may
be dangerous for the user.
2 - SAFETY
Heat safety
Before contacting one of our Approved Service Centres (see enclosed list),
ensure that:
– the appliance is set to normal operating mode;
– the air inlet and outlet grills are totally clear.
In the event of abnormal overheating, a safety device shuts down the appliance
and then automatically restarts it once ithas cooled. If the fault persists or gets
worse, a thermal fuse shuts the appliance down definitively and it must then be
taken to an approved service centre.
1 Jahr Garantie
gemäß einliegenden Bedingungen. Nur gültig
mit Kassenbon.
1 year guarantee
according to enclosed conditions.
1 année garantie
selon conditions ci-jointes.
1 año de garantía
según condiciones adjuntas.
Stempel des Fachhändlers
Stamp of your dealer
Cachet de votre magasin
Carimbo de vendedor autorizade
Verkaufsdatum
Date of purchase
Date de la vente
Data de venda
|