Instruction Manual
Thank you for purchasing the Roland GK-KIT-GT3, a divided pickup kit. The GK-KIT-GT3 is a specialized kit for internal installation of
the guitar divided pickup.
To ensure proper installation – which is critical – and operation, please read this manual carefully.
IMPORTANT NOTES
In addition to the items listed under “USING THE UNIT SAFELY,” please read and observe the following:
351
●
Using the unit near power amplifiers (or other equipment
containing large power transformers) may induce hum.
●
Be sure to use the special cable supplied by us to connect the GK-
KIT-GT3 to the GK-compatible device for guitar. Use of any other
cable may cause unnecessary problems.
●
352b Noise may be produced if wireless communications devices, such
as cell phones, are operated in the vicinity of this unit. Such noise
could occur when receiving or initiating a call, or while conversing.
●
GK-KIT-GT3 cannot be used with guitars that have unusual or
customized string setups, or guitars strung with nylon, rubber, or
other non-metallic strings.
402
●
Never use benzine, thinners, alcohol or solvents of any kind, to
avoid the possibility of discoloration and/or deformation.
556
●
When connecting / disconnecting all wirings, grasp the connector
itself---never pull on the cable. This way you will avoid causing
shorts, or damage to the cable's internal elements.
●
901(FV) euillez suivre attentivement les instructions suivantes quand
vous manipulez la carte afin d'éviter tout risque d'endom-
magement des pièces internes par l'électricité statique.
901
●
To avoid the risk of damage to internal components that can be
caused by static electricity, please carefully observe the following
whenever you handle the board.
•
Toujours toucher un objet métallique relié à la terre (comme un
tuyau par exemple) avant de manipuler la carte pour vous
décharger de l'électricité statique que vous auriez pu accumuler.
Lorsque vous manipulez la carte, la tenir par les côtés. Évitez
de toucher aux composants ou aux connecteurs.
Avant de connecter tout câble, assurez-vous qu'il ne contient
aucune charge d'électricité statique. De telles charges peuvent
être transmises, par exemple, si l'autre extrémité du câble
touche à un tapis (ou autre objet) où il y a accumulation
d'électricité statique.
•
Before you touch the board, always first grasp a metal object
(such as a water pipe), so you are sure that any static electricity
you might have been carrying has been discharged.
•
•
•
•
When handling the board, grasp it only by its edges. Avoid
touching any of the electronic components or connectors.
Before you connect any cables, make sure they do not carry a
static electricity charge. Such charges can be transmitted, for
example, if the other end of the cable has been in contact with a
carpet (or other object) where there is a static electricity buildup.
Save the bag in which the board was originally shipped, and put
the board back into it whenever you need to store or transport it.
•
Conservez le sachet d'origine dans lequel était la carte lors de
l'envoi et remettez la carte dedans si vous devez la ranger ou la
transporter.
•
911
●
912
●
913
●
915
●
●
911(FN)* e toucher aucun chemin d'accès des cicuits imprimés.
Do not touch any of the printed circuit pathways.
●
912(FN) e jamais forcer lors de l'installation de la carte de circuits imprimés.
Never use excessive force when installing a circuit board.
When circuit board installation is complete, double-check your work.
●
913(FQ) uand l'installation de la carte de circuits imprimés est terminée,
revérifiez si tout est bien installé.
●
914(FA) vant d'entreprendre l'installation de cette unité, retirer les piles
de la guitare le cas échéant.
Install only the included circuit boards. Remove only the specified
screws.
962a In the interest of product improvement, the specifications and/or
915(FI)nstaller uniquement les carte de circuits imprimés ci-jointes.
●
●
appearance of this unit are subject to change without prior notice.
Enlevez seulement les vis indiquées.
●
Roland assumes no liability concerning any damage to the guitar
and GK-KIT-GT3 upon installing the GK-KIT-GT3. Please proceed
with the installation using cation and care at your own risk.
• For GK Volume (3 pins)...........................................................................1
• For Switches (8 pins)................................................................................1
• For Guitar Signal (2 pins)........................................................................1
• For Guitar Battery (2 pins)......................................................................1
Supplied parts contents
• Divided Pickup ........................................................................................1
• Preamp Board ...........................................................................................1
• GK Connector Board................................................................................1
• Connector Plate ........................................................................................1
• Pan Head Screw (for installing the Divided Pickup) (M3x20) ..........2
• Spring (for installing the Divided Pickup)...........................................2
• Pan Head Screw with Spring Washer
• GK Volume (50kΩ 20% B Curve).........................................................1
• LED (with wiring)....................................................................................1
• DOWN/S1, UP/S2 Switch (Momentary, Normal Operation) ...............2
• GUITAR/MIX/GK Select Switch (DPDT, ON-OFF-ON) .........................1
(for installing the GK Connector) (M3x10) ...........................................2
Parts should be arranged separately
• Screw (for installing the Connector Plate)............................................4
• Ground Wire .........................................2 (See “Wiring Diagrams” (*1))
Wirings
• For GK Connector-A (7 pins)..................................................................1
• For GK Connector-B (8 pins) ..................................................................1
USING THE UNIT SAFELY
The
symbol alerts the user to important instructions
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
The
symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the power-
cord plug must be unplugged from the outlet.
001
012d
•
Before using this unit, make sure to read the instruc-
tions below, and the Instruction Manual.
•
Immediately turn the power off, and request
servicing by your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, when:
..................................................................................................
002a
•
•
If smoke or unusual odor occurs
Objects have fallen into, or liquid has been
spilled onto the unit; or
•
Do not open or perform any internal modifications
on the unit.
..................................................................................................
•
•
The unit has been exposed to rain (or otherwise
has become wet); or
The unit does not appear to operate normally or
exhibits a marked change in performance.
003
•
Do not attempt to repair the unit, or replace parts
within it (except when this manual provides specific
instructions directing you to do so). Refer all
servicing to your retailer, the nearest Roland Service
Center, or an authorized Roland distributor
..................................................................................................
013
•
In households with small children, an adult should
..................................................................................................
provide supervision until the child is capable of
following all the rules essential for the safe
operation of the unit.
004
•
Never use or store the unit in places that are:
•
Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or are
Damp (e.g., baths, washrooms, on wet floors); or are
Humid; or are
Exposed to rain; or are
Dusty; or are
Subject to high levels of vibration.
..................................................................................................
022b
•
If the guitar includes a battery, remove the battery from
the guitar before attempting installation of this unit.
•
•
•
•
•
106
•
Never climb on top of, nor place heavy objects on
the unit.
..................................................................................................
011
•
Do not allow any objects (e.g., flammable material,
..................................................................................................
coins, pins); or liquids of any kind (water, soft
drinks, etc.) to penetrate the unit.
118c
•
Whenever you’ve removed any parts (screws,
washers, springs, etc.) used in attaching compo-
nents, be sure to keep them out of the reach of small
children in order to prevent them from being
swallowed accidentally.
..................................................................................................
014
•
Protect the unit from strong impact.
(Do not drop it!)
..................................................................................................
..................................................................................................
Copyright © 2004 ROLAND CORPORATION
For EU Countries
This product complies with the requirements of
European Directive 89/336/EEC.
All rights reserved. No part of this publication
may be reproduced in any form without the writ-
ten permission of ROLAND CORPORATION.
Attaching the Divided Pickup
1.The “Roland” logo and the cable should emerge from under sixth string.
Adjust R on the pickup in accordance with
the guitar on which the pickup is being installed.
2.Do not locate the Divided Pickup more than 20 mm from the bridge.
20.0 mm (Max.)
R Adjustment Screw
3.Position so each string passes over a pickup yoke.
Sixth Fifth Forth
string string string
* Compatible with guitars having a string spacing of 9.6–11.8 mm.
4.Adjust the pickup height and R so that the clearance between the each string
and pickup yoke is 1.0 mm when the string is pressed at the highest fret.
String
1.0 mm
(Max.)
Divided Pickup
Use the included screws and springs
to attach the pickup on the guitar.
Dimensions Unit : mm
● GK Connector Board
● Preamp Board
● Divided Pickup
102.3
95.1
3.6
(57.2)
37.9
10.8
28.0
32.0
2- 3.2
50.0
● Connector Plate
45.0
37.0
22.2
4- 3.3
2
* ...with yokes at maximum height
2- 3.2
C.L
16.3
C.L
r
Wirings
●
For Guitar Signal
●
For Guitar
Battery
● For GK Connector-A
● For GK Connector-B
● For GK Volume
● For Switches
1: RED
1: YELLOW
2–8: BLUE
1: RED
2: WHITE
3: BLACK
1: WHITE
2: SHIELD
3: ORANGE
4: YELLOW
5: GREEN
6: BLUE
1: WHITE
2: SHIELD
1: BLACK
2: WHITE
2–7: WHITE
7: PURPLE
8: GRAY
03782690 ’04-10-1N
When connect the wiring, check the number of pin
Wiring Diagram
Divided Pickup
and direction accordingly
Hold like this when
connecting /
disconnecting.
Check the
number of
This side
here!!
pin.
LED
GUITAR/MIX/GK Select Switch
8 pins
For GK Connector-B
Preamp Board
GK
For Switches
Connector
Board
2 pins
8 pins
8 pins
7 pins
WHITE
4
5
SHIELD
ORANGE
YELLOW
GREEN
BLUE
4
6
7 pins For GK Connector-A
5
8 pins
(*1)
(*1)
6
PURPLE
GRAY
DOWN/S1
Switch
3 pins
2 pins
2 pins
For GK Volume
UP/S2
Switch
WHITE
SHIELD
3
2
1
RED
WHITE
BLACK
BLACK WHITE
For Guitar Signal
* Max Input level is 12VP-P
GK Volume
50 kΩ 20 % B Curve
For Guitar Battery
(*2)
1
2
3
Guitar Volume
Guitar
Out Jack
+
–
Pickup
Buttery
(*2)
* When the guitar incorporates a battery
Circuit of guitar
Dimensional Drawing of the Hole
(If necessary, a hole for a rotation-stopper can be drilled.)
● DOWN/S1 Switch
● LED
● GK Volume
●
GUITAR/MIX/GK Select Switch
UP/S2 Switch
8.5 mm
7.8 mm
6.4 mm
7.5 mm
6.2 mm
15.0 mm
for a rotation-stopper
3.0 mm
for a rotation-stopper
2.4 mm
Installation Notes
1.Attach the connector to the connector plate with the supplied screws.
2.Attach the plate to the guitar with the screws.
* Mount GK Connector board so that small connection port should be placed
top toward guitar surface.
GK Connector Board
Wiring for GK Volume
1.Solder each signal wire of GK volume wiring with
volume 50 kΩ 20 % B Curve.
Wiring for Guitar Signal
Guitar surface
1.Solder uncovered wire (silver) to the earth (ground) of the guitar.
2.Solder the white wire to the guitar signals.
Small connection port
Uncovered ➔ Earth (ground) of the guitar
White ➔ Guitar signal
* Do not exceed 12Vp-p for input signal level.
Wiring for Switches (Select Switch, DOWN/S1 Switch, UP/S2 Switch)
1.Ground wire for each wiring is common.
7: PURPLE DOWN/S1
8: GRAY UP/S2
2: SHIELD
Connect ground
Wire the ground wires as shown in “Wiring Diagram” (*1).
2.Using rebounding switch (SPDT (OFF)-ON-(OFF))
for DOWN/S1, UP/S2, mounting can be simpler.
* Switch not included—must be acquired separately.
Wiring for Guitar Battery
If the guitar has a battery for powering the pickup and preamp, install
the wiring from the jack as shown in “Wiring Diagram” (*2).
Even if a plug is not inserted in the jack, when power is applied to the
GK connector, power from the battery is turned on.
* This function is enabled only for the circuit being turned on/off with
the battery’s negative terminal.
* This wiring is not necessary for guitars without internal batteries.
* This wiring is for switching the battery on and off; it is not used for
supplying power to the guitar.
* A current of 500 mA or less can be switched ON/OFF using
this circuit. Please use due caution; if current consumption exceeds
500 mA, this circuit cannot be used.
About Transcription for Each Controller
When you transcribe each controller into guitar itself or owner’s manual, please transcribe as below:
GK Volume
DOWN/S1 Switch ...DOWN/S1
UP/S2 Switch ...UP/S2
...GK VOL
Select Switch ...GUITAR
...MIX
...GK
|