M3T-FLX-144NSE
Converter Board for Connecting 160-core Flexible Board FLX160 to 144-pin 0.4-mm-pitch TQFP
User’s Manual
Keep safety first in your circuit designs!
z Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products
better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to
personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with
appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention
against any malfunction or mishap.
Notes regarding these materials
z These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited
to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to
Renesas Technology Corporation, Renesas Solutions Corporation or a third party.
z Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of
any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application
examples contained in these materials.
z All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information
on products at the time of publication of these materials, and are subject to change by Renesas Technology Corporation and
Renesas Solutions Corporation without notice due to product improvements or other reasons. It is therefore recommended that
customers contact Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product
distributor for the latest product information before purchasing a product listed herein. The information described here may contain
technical inaccuracies or typographical errors. Renesas Technology Corporation and Renesas Solutions Corporation assume no
responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information
published by Renesas Technology Corporation and Renesas Solutions Corporation by various means, including the Renesas home
page (http://www.renesas.com).
z When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and
algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the
information and products. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any
damage, liability or other loss resulting from the information contained herein.
z Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under
circumstances in which human life is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions
Corporation or an authorized Renesas Technology product distributor when considering the use of a product contained herein for any
specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
z The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or
reproduce in whole or in part these materials.
z If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from
the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport
contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
z Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the
products contained therein.
Precautions to be taken when using this product
z This product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your
program you have finished developing, be sure to make a judgment on your own risk that it can be put to practical use by performing
integration test, evaluation, or some experiment else.
z In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.
z Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge.
However, this does not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any
circumstances.
z This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not
fall under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when
used in Japan.
If the requirements shown in the "CAUTION" sentences are ignored,
the equipment may cause personal injury or damage to the products.
CAUTION
Rev.1.00
October 1, 2003
(1/4)
REJ10J0227-0100Z
5. Connection Procedure (See Figure 3)
The procedure for connecting the M3T-FLX-144NSE is shown
below.
Probe of emulation pod
(1) Mount the NQPACK144SE on the target board.
(2) Attach the YQPACK144SE on the NQPACK144SE.
(3) Secure the four corners of the YQPACK144SE with the
YQ-GUIDE's.
(4)
● Do not use the screws included with the
YQPACK144SE for fixing the YQPACK144SE.
● The screwdriver included with the NQPACK144SE is
used for fixing the HQPACK144SE. Do not use if for
fixing the YQ-GUIDE's.
M3T-FLX-144NSE
(5)
Be sure to use a
slotted screwdriver.
YQ-GUIDE (x4)
YQPACK144SE
(4) Connect the probe of the emulation pod to the
M3T-FLX-144NSE.
(3)
(5) Attach the M3T-FLX-144NSE on the YQPACK144SE.
(2)
(1)
NQPACK144SE
144-pin 0.4-mm-pitch
(144PFB-A) foot pattern
: No. 1 pin
Be sure to align the pins.
Figure 3 Connection procedure of the M3T-FLX-144NSE
6. External Dimensions and a Sample Foot Pattern
55.0
21.8
0.225
0.4
15.1
19.1
Unit: mm
Figure 4 External dimensions and a sample foot pattern of the M3T-FLX-144NSE
(3/4)
7. Precautions
CAUTION
Caution to Be Taken for This Product:
z When connecting the YQPACK144SE, be sure to use the included YQ-GUIDE's.
z Do not use the screws included with the YQPACK144SE to fix it.
IMPORTANT
Notes on This Product:
z We cannot accept any request for repair.
z For purchasing the NQPACK144SE, YQPACK144SE and HQPACK144SE, contact the following:
Daimaru Kogyo Ltd.
Tokyo Eletech Corporation
z For inquiries about the product or the contents of this manual, contact your local distributor.
8. Correspondence of Connectors CN1 and CN2
Table 2 Correspondence of the Connectors
CN1
1a
2a
IC1
GND
17
CN1
1b
2b
IC1
18
16
CN2
1a
2a
IC1
GND
20
CN2
1b
2b
IC1
19
21
3a
15
3b
14
3a
22
3b
23
4a
13
4b
12
4a
24
4b
25
5a
11
5b
10
5a
26
5b
27
6a
9
6b
8
6a
28
6b
29
7a
7
7b
6
7a
30
7b
31
8a
5
8b
4
8a
32
8b
33
9a
3
9b
2
9a
34
9b
35
10a
11a
12a
13a
14a
15a
16a
17a
18a
19a
20a
21a
22a
23a
24a
25a
26a
27a
28a
29a
30a
31a
32a
33a
34a
35a
36a
37a
38a
39a
40a
1
10b
11b
12b
13b
14b
15b
16b
17b
18b
19b
20b
21b
22b
23b
24b
25b
26b
27b
28b
29b
30b
31b
32b
33b
34b
35b
36b
37b
38b
39b
40b
GND
144
142
140
138
136
134
132
130
128
GND
126
124
122
120
118
116
114
112
110
GND
108
106
104
102
100
98
10a
11a
12a
13a
14a
15a
16a
17a
18a
19a
20a
21a
22a
23a
24a
25a
26a
27a
28a
29a
30a
31a
32a
33a
34a
35a
36a
37a
38a
39a
40a
36
GND
38
40
42
44
46
48
50
52
54
GND
56
58
60
62
64
66
68
70
72
GND
74
76
78
80
82
84
86
88
90
10b
11b
12b
13b
14b
15b
16b
17b
18b
19b
20b
21b
22b
23b
24b
25b
26b
27b
28b
29b
30b
31b
32b
33b
34b
35b
36b
37b
38b
39b
40b
GND
37
39
41
43
45
47
49
51
53
GND
55
57
59
61
63
65
67
69
71
GND
73
75
77
79
81
83
85
87
89
GND
GND
143
141
139
137
135
133
131
129
127
GND
125
123
121
119
117
115
113
111
109
GND
107
105
103
101
99
97
95
93
91
96
94
92
GND
(NC: No connection)
(4/4)
|