M32171T-PTC
Converter Board for M32171FxxFP (for In-circuit Connection)
User’s Manual
Keep safety first in your circuit designs!
z Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products
better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to
personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with
appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention
against any malfunction or mishap.
Notes regarding these materials
z These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited
to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to
Renesas Technology Corporation, Renesas Solutions Corporation or a third party.
z Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of
any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application
examples contained in these materials.
z All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information
on products at the time of publication of these materials, and are subject to change by Renesas Technology Corporation and
Renesas Solutions Corporation without notice due to product improvements or other reasons. It is therefore recommended that
customers contact Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product
distributor for the latest product information before purchasing a product listed herein. The information described here may contain
technical inaccuracies or typographical errors. Renesas Technology Corporation and Renesas Solutions Corporation assume no
responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information
published by Renesas Technology Corporation and Renesas Solutions Corporation by various means, including the Renesas home
page (http://www.renesas.com).
z When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and
algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the
information and products. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any
damage, liability or other loss resulting from the information contained herein.
z Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under
circumstances in which human life is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions
Corporation or an authorized Renesas Technology product distributor when considering the use of a product contained herein for any
specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
z The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or
reproduce in whole or in part these materials.
z If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from
the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport
contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
z Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the
products contained therein.
Precautions to be taken when using this product
z This product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your
program you have finished developing, be sure to make a judgment on your own risk that it can be put to practical use by performing
integration test, evaluation, or some experiment else.
z In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.
z Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge.
However, this does not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any
circumstances.
z This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not
fall under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when
used in Japan.
If the requirements shown in the "CAUTION" sentences are ignored,
the equipment may cause personal injury or damage to the products.
CAUTION
Rev.1.00
August 1, 2003
(1/4)
REJ10J0210-0100Z
5. Attaching Procedure
How to attaching the M32171T-PTC is shown below. (see
Figure 3)
Interface cables of the probe
(5)
(1) Mount the NQPACK144SD on the foot pattern of the
target system
(4) Clock selection switch
(2) Attach the YQPACK144SD to the NQPACK144SD.
(3) Secure the four corners of the YQPACK144SD with the
YQ-GUIDE’s.
(4) Set the clock selection switch.
EXT*1: The clock of pin XIN of the target board is
supplied to the MCU on the M32171T-PTC.
M32171T-PTC
INT:
The clock (10 MHz) on the M32171T-PTC is
supplied to the MCU.
(6)
(5) Connect the SDI MCU control interface cable and the SDI
trace interface cable of the emulator probe to the
M32171T-PTC.
YQ-GUIDE's (x4)
(6) Attach the M32171T-PTC to the YQPACK144SD.
(3)
*1: When “EXT” is selected, take notice that the automatic
oscillation does not occur. Connect the output of the
oscillator to pin XIN.
YQPACK144SD
NQPACK144SD
(2)
(1)
144-pin 0.5-mm-pitch
(144P6Q-A) foot pattern
: No. 1 pin position
Be sure to align the pins.
Figure 3 Attaching procedure of the M32171T-PTC
6. External Dimensions and Sample Foot Pattern of the M32171T-PTC
0. 25
: No. 1 pin
16. 0
68. 0
LES -KLC
W1S
TXE
7. 0
TN I
M
A
D
E
M
3
2
1
7
0
T
P
T
C
A
0
I
N
.
J
6
f 3.2
(For SL)
A
P
A
N
-
6
0
0
0
7
.
.
R
E
V
A
.
3
9
2
1
.
3-f 1.0
Hole for soldering NQ
2J
1J
0. 5
0
.
4
19. 0
23. 0
3
Figure 4 External dimensions and sample foot pattern of the M32171T-PTC
(3/4)
7. Precautions
CAUTION
Cautions for the emulator:
z For debugging, be sure to use this product in a combination with the emulator M32100T2-SDI-E, M32170T-SDI or
M32100T-SDI-E.
z When starting up the PD32R, select an MCU file according to an MCU and operation mode. For selecting an MCU
file, refer to the release notes of the debugger.
z Connect both the SDI MCU control interface cable (10-conductor) and SDI trace interface cable (20-conductor) to
the emulator.
z For the precautions for a combination with an emulator, refer to the user’s manual of each emulator.
Cautions for Differences Between the Emulator and an actual MCU:
z The M32170F6VWG (768 KB of internal flash ROM and 40 KB of internal RAM) on the M32171T-PTC is used
for debugging. Take care of differences of internal memory sizes.
z When setting the clock selection switch to “EXT”, connect the clock generated by an oscillator of the target system
to pin XIN. The automatic oscillation between XIN and XOUT does not occur.
z Load capacity of all the signal lines of the MCU becomes greater than that of the actual signal lines on the MCU.
Therefore, for a part where timing is critical, Give due consideration to its connection
Cautions to Be Taken for This Product:
z When attaching the YQPACK144SD, be sure to use the included YQ-GUIDE’s.
IMPORTANT
Notes on This Product:
z We cannot accept any request for repair.
z To purchase NQPACK144SD and HQPACK144SD, contact the following.
z For inquiries about this product or the contents of this manual, contact your local distributor.
(4/4)
|