28409_SSD-250_IB 7/27/05 2:20 PM Page 1
®
Use and Care Guide
Faster Drying,
Less Damage
SSD-250
28409_SSD-250_IB 7/27/05 2:20 PM Page 4
Safety Instructions
above testing procedure, should the indi-
cator device not function properly, call
Remington Customer Service at
ALCI SAFETY DEVICE
This hair dryer is provided with an
appliance leakage circuit interrupter (ALCI)
safety device built into the plug. This
device is designed to make the
800-736-4648.
Should the ALCI safety device trip (i.e.,
reset button pops out) during use, press
the reset button. Should the dryer fail to
reset, call Remington Customer Service
at 800-736-4648. Never operate this
appliance if it has been dropped in water.
unit inoperable under some abnormal
conditions, such as accidental immersion
in water. The ALCI safety device is
equipped with a test button so that its
operation can be checked. This unit should
be tested before each use to confirm that
the safety device is operational.
This message about
Ground Fault Circuit
Interrupters
can save a life!
OVERHEATING
This appliance is equipped with an auto-
matic thermal limiter, which will cycle off
when overheated and come back on when
cooled down. If the unit cycles off, unplug
the cord for several minutes before
restarting.
If you must use your hair dryer in
the bathroom, install a GFCI* now!
To Test:
After plugging in your hair dryer:
Your local electrician can help you decide which type is best for you–a
portable unit that plugs into the electrical outlet or a permanent unit
installed by your electrician. The National Electrical Code now requires
GFCI’s in bathrooms, garages, and outdoor outlets of all new homes.
■
■
Press the reset button on the
ALCI device.
Press the test button. The reset button
will pop out. This verifies that the
safety device is operating properly.
Press the reset button to reactivate
your ALCI safety device.
Why do you need a GFCI?
Electricity and water don’t mix. If your hair dryer falls in water while it’s
plugged in, the electric shock can kill you… even if the switch is “off.”
A regular fuse or circuit breaker won’t protect you under these circum-
stances. A GFCI offers you greater protection.
■
■
Your hair dryer is now ready for use.
A GFCI can save your life!
Compared to that, the price is small!
Note: This unit may automatically trip
when unplugged. If so, unit must be reset
after it is plugged in. After following the
Don’t wait… install one now!
*GFCI is a sensitive device which reacts immediately to a small electric
current leak by stopping the electricity flow.
4
5
28409_SSD-250_IB 7/27/05 2:20 PM Page 6
Product Features
®
®
SuperSonic Features
SuperSonic Dryer Technology
Wet hair holds 90% of its
moisture in its inner layer. Air
that is too hot causes hair’s
outer layer to seal shut –
trapping water inside and slowing
down the drying process.
• More powerful motor & fan design
• Larger air intake area
• Fast air concentrator
• 1875 watts
Ionic conditioning
Negative ions neutralize the
positive ions that cause
static and frizzies. Leaves hair
shiny and healthy-looking.
before
after
• 2 heat settings
• 2 speed settings
• Cool Shot button
• Easy-to-clean grille
• 6-foot cord with hang loop
• Dual voltage
• Ionic conditioning
• Ceramic radiant heat technology
• Mid-size design
Ceramic radiant heat
technology
The SuperSonic® dryer gener-
ates more airflow so it can
use less heat to dry hair more
quickly. And less heat equals
less hair damage.
Ceramic emits far-infrared,
radiant heat to help dry water
molecules inside the hair
strand. This fast and efficient
process helps prevent heat
damage for less frizz and
more shine.
Ceramic-
Coated
Grille
Fast air concentrator
Exclusive vent design
pulls in more air for faster
precision styling.
1875 watts
Overheating
Air Intake
Grille
This appliance is equipped with an auto-
matic thermal limiter, which will cycle off
when overheated and come back on when
cooled down. If the unit cycles off, unplug
the cord for several minutes before
restarting.
Fast Air
Concentrator
Cool Shot button
2 Heat/Speed
Settings
6-Foot Cord
with
Hang Loop
Dual Voltage
Selector
7
6
28409_SSD-250_IB 7/27/05 2:20 PM Page 8
Cleaning and Maintenance
How to Use
For curly hair:
Use dryer on a low heat and speed setting
Basic Drying Techniques
Maintenance Instructions
Cleaning Instructions
The air filter should be cleaned regularly,
since a dirty or clogged filter will impair the
efficiency of the dryer.
1. To clean air filter, make sure dryer is
turned off and unplugged.
2. Use a soft bristle brush to gently remove
any particles that are lodged in filter.
3. If the unit is dirty, wipe it with a dampcloth.
The dryer needs minimum maintenance to
ensure the best performance and long life.
■ Do not attempt to repair the appliance
yourself.
1. Gently towel dry hair to remove excess
water. Avoid rubbing hair with towel –
this creates split ends and frizziness.
Detangle hair with a wide-toothed comb.
2. Be sure dryer is turned off. Plug dryer
into an electrical outlet.
and move it quickly about your head. As
you dry your hair, scrunch it with your
favorite styling product or twirl strands of
hair around your fingers to add definition.
When finished drying, lock in the style with
the Cool Shot.
■ Keep all intake openings clear of dust
accumulation. See “Cleaning Instructions.”
No other maintenance or lubrication is
required.
■ If the cord becomes twisted due to use,
periodically straighten it. Store appliance
and cord where they will not be dam-
aged. Do not wrap cord around dryer.
3. Turn the dryer on and set it to a high
heat and speed. Remove some of the
additional moisture from your hair by
briskly blow drying it all over, using your
fingers to "comb" through hair.
4. When hair is almost dry, lower the heat
and speed to the desired settings and
begin to style.
5. Divide hair into manageable sections.
Begin at the nape of your neck and
brush hair, following the movement of
the brush with the dryer. Continue
working your way up to your scalp, then
to the sides and the front, drying small
sections at a time.
6. Once your desired style is achieved,
push the Cool Shot button to set the style
with a cool flow of air.
Hair Care Tips
■ Keep the dryer about 8 inches away
from your head to avoid burning scalp or
damaging hair.
■ Always keep the dryer pointed down the
hair shaft to smooth the cuticle and
create a silky, shiny style.
■ To help prevent heat damage and add
shine, spritz damp hair with a heat
protection spray before blow drying.
■ To create a style with lots of body, apply
volumizing mousse to towel-dried hair.
Distribute it evenly from roots to ends,
then blow dry as usual. Hair will be soft,
shiny, and full of volume.
■ For a super smooth, salon-like blow dry,
finish by running a straightening iron
over dried hair.
■ For a quick touch-up between sham-
poos, mist hair to dampen it, then style
with dryer.
Storage
When not in use, unplug the unit. Allow it
to cool, and store out of reach of children in a
safe, dry location. Never wrap the cord
around the appliance, as this will cause
the cord to wear prematurely and break.
Handle the cord carefully, and avoid jerking,
twisting, or straining it, especially at plug
connections.
International Operation
International Operation
The SuperSonic® hair dryer is perfect for
home or travel abroad. The dryer converts
easily to foreign voltages so it can accompany
you anywhere.
indicator lines up with the desired voltage. The
250 volt setting can be used in any country
that operates at a voltage greater than 125.
In a 220/240 volt country, the dryer will oper-
ate only on the LOW setting. Do not force the
unit to the HIGH setting—the HIGH setting will
not work at 250 volts. Even though the dryer
is set to LOW, the higher voltage coming into
the unit results in the unit operating at a HIGH
heat/airflow. The LOW setting on 250 volts will
provide full heat and airflow to dry your hair.
For straight, smooth hair:
In North America
With the dryer turned off, attach the
concentrator to the end of the nozzle. Turn
the driver on and brush hair from under-
neath using a large, round brush or paddle
brush. Pull hair down until the hair is fully
extended and taut. Run the dryer slowly
down the length of the hair several times
until dry. Repeat with all sections of hair
until it is completely dried. Lock in the style
with the Cool Shot.
Your dryer is pre-set to run on North American
voltage (125 volts), so no voltage adjustment
is necessary before using it in Canada,
Mexico, or the United States.
Outside North America
Many foreign countries operate on 220/240
voltage. If you plan to travel to a country that
uses 220/240 volts, you will need to set the
dryer’s voltage selector to 250 volts before
you can use it there. With the
A plug adapter is necessary when traveling to
countries where the 220/240 volt setting is
required. 220/240-volt plugs are configured
differently from country to country, however,
so make sure to buy the appropriate adapter
for the area you’re visiting (square, round,
two- or three-pronged). Adapters are sold at
local appliance and hardware stores at a
modest cost.
dryer turned off, insert a
coin or screwdriver into
the slot on the dryer’s 125
250
dual voltage selector.
Then turn it so that the
Selector Button
9
8
28409_SSD-250_IB 7/27/05 2:20 PM Page 10
Warranty
KEEP ORIGINAL SALES RECEIPT AS
SPECTRUM BRANDS, INC. SHALL NOT
BE RESPONSIBLE FOR ANY INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS
PRODUCT. ALL IMPLIED WARRANTIES,
INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF FITNESS AND
MERCHANTABILITY, ARE LIMITED IN
DURATION TO TWO YEARS FROM DATE
OF ORIGINAL PURCHASE.
125/250 VAC 50/60Hz 1875 watts
Full Four-Year Warranty
Spectrum Brands, Inc. warrants this product
against any defects that are due to faulty
material or workmanship for a four-year
period from the original date of consumer
purchase. This warranty does not include
damage to the product resulting from
accident or misuse.
If the product should become defective
within the warranty period, we will repair it
or elect to replace it free of charge. Return
your product and sales receipt with your
name, address and day time phone number
to: Spectrum Brands, Inc., Attention:
Consumer Services, 601 Rayovac Drive,
Madison, WI 53711. For more information
call 800-736-4648.
PROOF OF PURCHASE FOR WARRANTY
PURPOSES.
U.S. Patent 483,521 and Patent Pending
This warranty does not cover products
damaged by the following:
Questions or comments:
Call 800-736-4648 in U.S.
Or visit www.remington-products.com
■
Accident, misuse, abuse or alteration
of the product
■
■
■
Servicing by unauthorized persons
Use with unauthorized accessories
Connecting it to incorrect current and
voltage
Dist. by: Spectrum Brands, Inc.,
Madison, WI 53711
This warranty gives you specific legal rights
and you may also have other rights which
vary from state to state or province to
province. Some states do not allow the
exclusion or limitation of incidental, special
or consequential damages.
REMINGTON and SUPERSONIC are
registered trademarks of ROVCAL, INC.
■
■
Wrapping cord around appliance
causing premature wear & breakage
Any other conditions beyond our control
©2005 ROVCAL, INC.
07/05 Job# CS28409
T22-17446
No responsibility, obligation, or liability is assumed
for the installation or maintenance of this product.
Spectrum Brands, Inc.
800-736-4648
Spectrum Brands, Inc.
Money-back Offer
MADE IN CHINA
If within 30 days after you have purchased
your Remington® branded product, you are
not satisfied and would like a refund, return
it with the sales slip indicating purchase
price and date of purchase to the retailer
from whom it was purchased. Spectrum
Brands, Inc. will reimburse all retailers who
accept the product within 30 days from the
date of purchase. If you have any questions
concerning the money-back guarantee,
please call 800-736-4648.
10
11
28409_SSD-250_IB 7/27/05 2:20 PM Page 12
|