OPERATOR’S MANUAL
18 VOLT RECIPROCATING SAW
VARIABLE SPEED
R8442
®
Your reciprocating saw has been engineered and manufactured to our high standards for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
1
GENERAL SAFETY RULES
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enable better
control of the tool in unexpected situations.
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal
injury.
Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
SAVE THESE INSTRUCTIONS
WORK AREA
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks which
may ignite the dust or fumes.
TOOL USE AND CARE
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for which it is designed.
ELECTRICAL SAFETY
A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a risk
of fire when used with another battery.
Do not use tool if switch does not turn it on or off.
A tool that cannot be controlled with the switch is
dangerous and must be repaired.
Disconnect battery pack from tool or place the
switch in the locked or off position before making
any adjustments, changing accessories, or storing
the tool. Such preventive safety measures reduce the
risk of starting the tool accidentally.
Use battery operated tool only with specifically
designated battery pack. Use of any other batteries may
create a risk of fire.
Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys, nails,
screws, or other small metal objects that can make
a connection from one terminal to another. Shorting
the battery terminals together may cause sparks, burns,
or a fire.
Use battery only with charger listed.
MODEL
R8442
BATTERY PACK
130254003
CHARGER
140276001,140276002
140276003, 140276004
130254007
Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
PERSONAL SAFETY
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp
cutting edges are less likely to bind and are easier to
control.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may
be suitable for one tool may create a risk of injury when
used on another tool.
Keep the tool and its handle dry, clean and free
from oil and grease. Always use a clean cloth when
cleaning. Never use brake fluids, gasoline, petroleum-
based products, or any strong solvents to clean your tool.
Following this rule will reduce the risk of loss of control
and deterioration of the enclosure plastic.
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use tool while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal
injury.
Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery pack.
Carrying tools with your finger on the switch or inserting
the battery pack into a tool with the switch on invites
accidents.
Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
3
GENERAL SAFETY RULES
When servicing a tool, use only identical replacement
parts. Follow instructions in the Maintenance section
of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of
shock or injury.
SERVICE
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed by
unqualified personnel may result in a risk of injury.
SPECIFIC SAFETY RULES
Never use a battery that has been dropped or
received a sharp blow. A damaged battery is subject to
explosion. Properly dispose of a dropped or damaged
battery immediately.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring. Contact with a “live” wire will
also make exposed metal parts of the tool “live” and
shock the operator.
Batteries vent hydrogen gas and can explode in the
presence of a source of ignition, such as a pilot light.
To reduce the risk of serious personal injury, never use
any cordless product in the presence of open flame. An
exploded battery can propel debris and chemicals. If
exposed, flush with water immediately.
Wait for the cutter to stop before setting the tool down.
An exposed cutter may engage the surface leading to
possible loss of control and serious injury.
Know your power tool. Read operator’s manual
carefully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of electric
shock.
For best results, your battery tool should be charged
in a location where the temperature is more than
50°F but less than 100°F. Do not store outside or in
vehicles.
Always wear safety glasses with side shields.
Everyday glasses have only impact resistant lenses. They
are NOT safety glasses. Following this rule will reduce
the risk of eye injury.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in contact
with your skin, wash immediately with soap and water,
then neutralize with lemon juice or vinegar. If liquid
gets into your eyes, flush them with clean water for
at least 10 minutes, then seek immediate medical
attention. Following this rule will reduce the risk of serious
personal injury.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the risk
of serious personal injury.
Protect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions
also.
Do not place battery tools or their batteries near
fire or heat. This will reduce the risk of explosion and
possibly injury.
4
SAFETY RULES FOR CHARGER
chemicals that can damage, weaken, or destroy
plastic.
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal
injury.
An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
Before using battery charger, read all instructions and
cautionary markings in this manual, on battery charger,
battery, and product using battery to prevent misuse of
the products and possible injury or damage.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger as specified below:
CAUTION:
Cord Length (Feet)
Cord Size (AWG)
25'
16
50'
16
100'
16
To reduce the risk of electric shock or damage
to the charger and battery, charge only nickel-
cadmium rechargeable batteries as specifically
designated on your charger. Other types of
batteries may burst, causing personal injury or
damage.
NOTE: AWG = American Wire Gauge
Do not operate charger with a damaged cord or
plug, which could cause shorting and electric shock. If
damaged, have the charger replaced by an authorized
serviceman.
Do not use charger outdoors or expose to wet or damp
conditions. Water entering charger will increase the risk
of electric shock.
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way. Take
it to an authorized serviceman for electrical check to
determine if the charger is in good working order.
Use of an attachment not recommended or sold by the
battery charger manufacturer may result in a risk of
fire, electric shock, or injury to persons. Following this
rule will reduce the risk of electric shock, fire, or serious
personal injury.
Do not disassemble charger. Take it to an authorized
serviceman when service or repair is required. Incorrect
reassembly may result in a risk of electric shock or fire.
Unplug charger from outlet before attempting
any maintenance or cleaning to reduce the risk of
electric shock.
Do not abuse cord or charger. Never use the cord to
carry the charger. Do not pull the charger cord rather than
the plug when disconnecting from receptacle. Damage
to the cord or charger could occur and create an electric
shock hazard. Replace damaged cords immediately.
Disconnect charger from the power supply when
not in use. This will reduce the risk of electric shock or
damage to the charger if metal items should fall into the
opening. It also will help prevent damage to the charger
during a power surge.
Make sure cord is located so that it will not be stepped
on, tripped over, come in contact with sharp edges
or moving parts or otherwise subjected to damage or
stress. This will reduce the risk of accidental falls, which
could cause injury, and damage to the cord, which could
result in electric shock.
Risk of electric shock. Do not touch uninsulated portion
of output connector or uninsulated battery terminal.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions also
to prevent misuse of the product and possible injury.
Keep cord and charger from heat to prevent damage
to housing or internal parts.
Do not let gasoline, oils, petroleum-based products,
etc. come in contact with plastic parts. They contain
IMPORTANT SAFETY INSTRUCTIONS
1. SAVE THESE INSTRUCTIONS
This manual contains important safety and operating instructions for battery charger 140276003.
2. Before using battery charger, read all instructions and cautionary markings on battery charger, battery, and product
using battery.
3. CAUTION: To reduce the risk of injury, charge only nickel-cadmium rechargeable batteries. Other types of batteries
may burst, causing personal injury or damage.
5
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-
tion of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Frequency (cycles per second)
Watt
Power
min
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic of current
Rotational speed, at no load
n
No Load Speed
o
Class II Construction
Per Minute
Double-insulated construction
Revolutions, strokes, surface speed, orbits etc., per minute
.../min
Do not expose to rain or use in damp locations.
Wet Conditions Alert
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Hot Surface
To reduce the risk of injury or damage, avoid contact with any
hot surface.
6
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
WARNING:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
CAUTION:
SERVICE
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
WARNING:
To avoid serious personal injury, do not attempt
to use this product until you read thoroughly and
understand completely the operator’s manual.
Save this operator’s manual and review frequently
for continuing safe operation and instructing others
who may use this product.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses
with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask for use
over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked
to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
7
FEATURES
PRODUCT SPECIFICATIONS
Strokes Per Minute.........................................0-2, 500/min.
Charger Input ................................... 120 V, 60 Hz, AC only
Charge Rate ...................................................... 30 minutes
Length of Stroke...................................................1-3/16 in.
Motor..................................................................18 Volt DC
Switch..........................................................Variable Speed
LOCK-OFF
BUTTON
SWITCH
TRIGGER
SHOE
ASSEMBLY
®
SAW
BLADE
BATTERY
PACK
BLADE CLAMP
LOCK / RELEASE
LEVER
CHARGER
4-1/8 in.
Fig. 1
8
FEATURES
KNOW YOUR RECIPROCATING SAW
TOOLLESS BLADE CLAMP
Your saw has a blade clamp design that does not require
the use of a tool (blade wrench) when installing or removing
the blade.
See Figure 1.
Before attempting to use this product, familiarize yourself
with all operating features and safety rules.
VARIABLE SPEED
The variable speed switch trigger delivers higher speed
with increased trigger pressure and lower speed with
decreased trigger pressure.
CHARGER
The charger has a key-hole hanging feature for convenient,
space-saving storage. Screws should be installed so that
the center distance is 4-1/8 in.
LOCK-OFF BUTTON
Your saw is equipped with a “lock-off” button which reduces
the possibility of accidental starting. The lock-off button is
located on the handle above the switch trigger.
ASSEMBLY
UNPACKING
This product has been shipped completely assembled.
WARNING:
If any parts are damaged or missing, do not
operate this tool until the parts are replaced.
Failure to heed this warning could result in serious
personal injury.
Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list are
included.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have
WARNING:
carefully inspected and satisfactorily operated the tool.
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading
to possible serious personal injury.
If any parts are damaged or missing, please call
1-866-539-1710 for assistance.
PACKING LIST
18 Volt Reciprocating Saw
Saw Blade Pack (2)
Battery
Charger
WARNING:
To prevent accidental starting that could cause
serious personal injury, always remove the battery
pack from the tool when assembling parts.
Tool Bag
Operator’s Manual
9
OPERATION
WARNING:
Do not allow familiarity with your tool to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
WARNING:
Always wear safety goggles or safety glasses with
side shields when operating tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
WARNING:
Do not use any attachments or accessories
not recommended by the manufacturer of this
tool. The use of attachments or accessories not
recommended can result in serious personal injury.
Fig. 2
APPLICATIONS
Attach the battery pack to the charger by aligning the
raised ribs on the battery pack with the grooves in the
charger, then slide the battery pack onto the charger. See
Figure 2.
You may use this tool for the purposes listed below:
Cutting all types of wood products (lumber, plywood,
paneling, composition board, and hard wood)
Cutting masonite and plastic
The battery pack will become slightly warm to the touch
while charging. This is normal and does not indicate a
problem.
Do not place the charger in an area of extreme heat or
cold. It will work best at normal room temperature.
FFoorr averaaggee charge times, refer to the chart on the
following page.
When tthhee batteries become fully charged, unplug the
charger from the power supply and remove the battery
pack.
Cutting drywall
Cutting metals such as sheet steel, pipe, steel rods,
aluminum, brass, and copper
CAUTION:
If at any point during the charging process none
of the LEDs are lit, remove the battery pack from
the charger to avoid damaging the product. DO
NOT insert another battery. Return the charger and
battery to your nearest service center for service
or replacement.
CHARGING A HOT BATTERY PACK
When using the tool continuously, the batteries in the
battery pack will become hot. You should let a hot
battery pack cool down for approximately 20 minutes before
attempting to recharge.
CHARGING THE BATTERY PACK
If the battery pack is above normal temperature range, the
red LED will begin flashing and the green LED will be off.
When the battery pack cools down to approximately 104°F
(40°C), the charger will automatically begin fast charge mode.
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it until the light on front of charger changes
from flashing green to continuous green.
NOTE: Batteries will not reach full charge the first time they
are charged. Allow several cycles (operation followed by
recharging) for them to become fully charged. This is normal
for nickel-cadmium batteries.
CHARGING A COOL BATTERY PACK
If the battery pack is below normal temperature range, the
red LED will begin flashing and the green LED will be off.
When the battery warms to a temperature of more than 41°F
(5°C), the charger will automatically begin fast charge mode.
TO CHARGE
Charge the battery pack only with the charger provided.
Make sure the power supply is normal household voltage,
120 volts, 60 Hz, AC only.
NOTE: Refer to CHARGING THE BATTERY PACK for
normal recharging of batteries. If the charger does not charge
your battery pack under normal circumstances, return both
the battery pack and charger to your nearest repair center
for electrical check. For the location of your nearest repair
center, please call 1-866-539-1710.
Connect the charger to a power supply.
10
OPERATION
LED FUNCTION OF CHARGER
See Figure 3.
LED
INDICATOR
BATTERY
PACK
RED
LED
GREEN
LED
ACTION
Power
Without battery pack ON
OFF
Ready to charge battery pack
When battery pack reaches cooled
temperature, charger begins fast
charge mode
Evaluate
Evaluate
Hot battery pack
Cold battery pack
Flashing
OFF
OFF
When battery pack reaches warmed
temperature, charger begins fast
charge mode
Flashing
Charger pre-charges battery until nor-
mal voltage is reached, then begins
fast charge mode
Evaluate
Defective
Deeply discharged
Defective
Flashing
Flashing
OFF
Flashing
Battery pack or charger is defective.
• If defective, try to repeat the conditions a second time by removing and reinstalling the battery
pack. If the LED status repeats a second time, try charging a different battery.
• If a different battery charges normally, dispose of the defective pack (see Maintenance section).
• If a different battery also indicates “Defective,” the charger may be defective.
Charging
Full
Fast charging
Slow charging
ON
Flashing
ON
See chart below for charge times
Fast charging is complete.
Charger maintains charge mode.
OFF
GREEN LED
POWER
BATTERY
AVERAGE CHARGE TIME
RED LED
INDICATOR
COMPACT SERIES
18 min.
27 min.
34 min.
EVALUATE
INDICATOR
HC
HC 2.5
DEFECTIVE
INDICATOR
CHARGING
INDICATOR
NOTE: The 9.6 Volt, 12 Volt, and 14.4 Volt battery
packs will not slide all the way down onto the char-
ger port. Insert 9.6 Volt, 12 Volt, and 14.4 Volt battery
packs until they click into place and are aligned with
the line on the charger, shown at left.
FULL
INDICATOR
Allow up to 5 seconds for the “charge” light to come
on after the battery pack is inserted.
Fig. 3
11
OPERATION
TO INSTALL BATTERY PACK
See Figure 4.
Place the battery pack in the saw aligning raised rib on
®
battery pack with groove in the saw’s battery port.
Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured to saw
before beginning operation.
CAUTION:
RAISED RIB
When placing battery pack in the tool, be sure
raised rib on battery pack aligns with the grooves
in the bottom of the saw and latches into place
properly. Improper installation of the battery pack
can cause damage to internal components.
Fig. 4
BATTERY PACK
®
TO REMOVE BATTERY PACK
See Figure 5.
Locate the latches on the side of the battery pack and
depress both sides to release the battery pack from the
saw.
Remove the battery pack from the saw.
DEPRESS LATCHES TO
RELEASE BATTERY PACK
Fig. 5
SHOE ASSEMBLY
See Figure 6.
HEX KEY
The shoe assembly of the reciprocating saw pivots up and
down in both directions. The base is adjustable, allowing the
use of the blade teeth at different positions on the blade.
CHANGING POSITIONS OF THE BASE
ASSEMBLY
See Figure 6.
Remove the battery pack.
Loosen the screws in the gear frame with the hex key.
SCREWS
Reposition the base assembly.
Retighten the button head screws securely. Do not
overtighten screws or use an aid with the hex key.
BASE ASSEMBLY
Fig. 6
Remove the hex key.
TO INSTALL SAW BLADE
See Figure 7.
Remove the battery pack from the saw.
®
Lift the blade clamp lock/release lever located on the side
of the saw.
Insert saw blade between blade clamp and saw bar.
BLADE
CLAMP
BLADE
Lock the blade clamp lever.
GENERAL CUTTING
See Figure 8.
Rest the front of the saw shoe on the workpiece and align
cutting edge of the blade with the line on the workpiece.
Startthesawandmoveitforwardontheworksurface. Apply
downwardpressuretokeepthesawsteadyandonlyenough
forward pressure to keep the blade cutting.
Fig. 7
12
OPERATION
CAUTION:
Do not force the saw. Forcing the saw may
overheat the motor and break saw blades.
PLUNGE CUTTING
See Figure 9.
®
WARNING:
To avoid loss of control, broken blades, or dam-
age to the material being cut, always use extreme
caution when making plunge cuts. It is not rec-
ommended to plunge cut materials other than
wood.
Mark the line of cut clearly on the workpiece.
Fig. 8
Tilt the saw forward so that it rests on the front edge
of the shoe and blade will not come in contact with the
workpiece when the saw is turned on.
Make sure the blade is inside the area to be cut.
Using high speed, start the saw and slowly lower the
blade into the workpiece until the blade cuts through the
wood.
®
Continue lowering the blade into the workpiece until the
shoe rests flat on the work surface, then move the saw
forward to complete the opening.
Use only the 7 teeth per inch blade for this type of cut.
METAL CUTTING
See Figure 10.
Many kinds of metals can be cut with the saw. Be careful
not to twist or bend the blades. Do not force. If the blade
chatters or vibrates excessively, use a finer-tooth metal-
cutting blade. If blade heats excessively, use lower speed. If
blade teeth become filled or clogged when cutting soft met-
als, such as aluminum, use a coarser-tooth blade or lower
speed.Werecommenduseofoilwhencuttingmetalstokeep
blades cool, increase cutting action, and prolong blade life.
Clamp the work firmly and saw close to the clamping point
to eliminate any vibration of the work being cut.
Fig. 9
®
When cutting conduit, pipe, or angle iron, clamp work in a
vise if possible and saw close to the vise. To cut thin sheet
materials, “sandwich” the material between hardboard or
plywood and clamp the layers to eliminate vibration and
material tearing. By doing this, the material will be cut
smoothly. Lay out your pattern or line of cut on top of the
“sandwich.”
NOTE: When cutting metal, keep exposed portion of saw
blade clean and free of metal chips by wiping frequently with
an oily cloth. Use extreme caution in disposing of oily cloth
after completion of job to prevent potential fire hazard.
Fig. 10
13
MAINTENANCE
GENERAL MAINTENANCE
WARNING:
When servicing use only identical RIDGID
replacement parts. Use of any other parts may
create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a
dust mask.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at a RIDGID authorized service center.
WARNING:
To avoid serious personal injury, always remove
the battery pack from the tool when cleaning or
performing any maintenance.
BATTERY PACK REMOVAL AND PREPARATION
BATTERIES
The battery pack for this tool is equipped with nickel-cad-
mium rechargeable batteries. Length of service from each
charging will depend on the type of work you are doing.
FOR RECYCLING
To preserve natural resources, please
recycle or dispose of batteries
properly.
The batteries in this tool have been designed to provide
maximum trouble-free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry, could
result in a serious burn.
This product contains nickel-cadmium
batteries. Local, state or federal
laws may prohibit disposal of nickel-
cadmium batteries in ordinary trash.
Consult your local waste authority for information regarding
available recycling and/or disposal options.
To obtain the longest possible battery life, we suggest the
following:
Remove the battery pack from the charger once it is fully
WARNING:
charged and ready for use.
Upon removal, cover the battery pack’s terminals
with heavy-duty adhesive tape. Do not attempt
to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below
80°F.
Store battery packs in a “discharged” condition.
14
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL
3 YEAR LIMITED SERVICE WARRANTY
Proof of purchase must be presented when requesting war-
ranty service.
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at retail
and may not be transferred. This warranty only covers de-
fects arising under normal usage and does not cover any
malfunction, failure or defect resulting from misuse, abuse,
neglect, alteration, modification or repair by other than an
authorized service center for RIDGID® branded hand held
and stationary power tools. Consumable accessories pro-
vided with the tool such as, but not limited to, blades, bits
and sand paper are not covered.
Limited to RIDGID® hand held and stationary power tools
purchased 2/1/04 and after. This product is manufactured
by One World Technologies, Inc. The trademark is licensed
from RIDGID, Inc. All warranty communications should be
directed to One World Technologies, Inc., attn: RIDGID Hand
Held and Stationary Power Tool Technical Service at (toll
free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
During the first 90 days after the date of purchase, if you are
dissatisfied with the performance of this RIDGID® Hand Held
and Stationary Power Tool for any reason you may return
the tool to the dealer from which it was purchased for a full
refund or exchange. To receive a replacement tool you must
present proof of purchase and return all original equipment
packaged with the original product. The replacement tool
will be covered by the limited warranty for the balance of
the 3 YEAR service warranty period.
RIDGID, INC. AND ONE WORLD TECHNOLOGIES, INC.
MAKE NO WARRANTIES, REPRESENTATIONS OR
PROMISES AS TO THE QUALITY OR PERFORMANCE
OF ITS POWER TOOLS OTHER THAN THOSE SPECIFI-
CALLY STATED IN THIS WARRANTY.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied war-
ranties, including warranties of MERCHANTABILITY or FIT-
NESS FOR A PARTICULAR PURPOSE, are disclaimed. Any
implied warranties, including warranties of merchantability
or fitness for a particular purpose, that cannot be disclaimed
under state law are limited to three years from the date of
purchase. One World Technologies, Inc. and RIDGID, Inc.
are not responsible for direct, indirect, incidental or conse-
quential damages. Some states do not allow limitations on
how long an implied warranty lasts and/or do not allow the
exclusion or limitation of incidental or consequential dam-
ages, so the above limitations may not apply to you. This
warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
WHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power
Tools covers all defects in workmanship or materials and nor-
mal wear items such as brushes, chucks, motors, switches,
cords, gears and even cordless batteries in this RIDGID®
tool for three years following the purchase date of the tool.
Warranties for other RIDGID® products may vary.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID® tool you must return it;
freight prepaid, or take it in to an authorized service center
for RIDGID® branded hand held and stationary power tools.
You may obtain the location of the authorized service center
nearest you by calling (toll free) 1-866-539-1710 or by log-
ging on to the RIDGID® website at www.ridgid.com. When
requesting warranty service, you must present the original
dated sales receipt. The authorized service center will re-
pair any faulty workmanship, and either repair or replace
any part covered under the warranty, at our option, at no
charge to you.
One World Technologies, Inc.
P.O. Box 35, Hwy. 8
Pickens, SC 29671
15
OPERATOR’S MANUAL
18 VOLT RECIPROCATING SAW
VARIABLE SPEED
R8442
Customer Service Information:
For parts or service, contact your nearest RIDGID authorized service center. Be
sure to provide all relevant information when you call or visit. For the location of
the authorized service center nearest you, please call 1-866-539-1710 or visit us
The model number of this tool is found on a plate attached to the motor housing.
Please record the serial number in the space provided below. When ordering repair
parts, always give the following information:
R8442
Model No.
Serial No.
983000-768
3-24-06 (REV:01)
|