Package Contents
Mounting the wall plate
Attaching the Arms to the TV
Final Installation and
Adjustment
Safety precautions
Bag #
(Ref) Item (Qty)
Fig. 3
Follow these precautions to ensure safe installation and
mounting of your flat panel TV.
(A) M4x12 Bolt (x4)
(B) M4x30 Bolt (x4)
Drywall Installation
Attach the arms to the back
of your display.
1
2
Important! For safety, this mount must be secured to
two adjacent wood studs no less than 16” apart.
1. With the help of another person, carefully lift your
display and place it on the wall plate (Fig. 5). Do not
release the display until the mounting arms have
securely hooked onto the crossbars!
1. Make sure these instructions are read and completely
understood before attempting installation. If you
are unsure of any part of this installation, contact a
professional installer for assistance.
(C) M4 Lock Washer (x4)
1. Using a stud finder, locate and mark two adjacent studs
LCD TV Wall Mount
Installation Manual
for securing the mount.
Important! Use extra
care during this part of the
installation. Avoid laying your
display face down if possible
as it may damage the viewing
surface.
(D) M5x12 Bolt (x4)
(E) M5x30 Bolt (x4)
2. Place the wall plate against the wall and level it using
2. The wall or mounting surface must be capable of
supporting the combined weight of the wall mount and
the display; otherwise the structure must be reinforced.
the bubble guide.
(F) M5 Lock Washer (x4)
3. Mark four locations (two per stud) on the wall where
the mount will be secured. Be sure to use the center of
each stud.
Fits TVs 23"- 37"
3. Protective eye wear and proper tools must be used.
A minimum of two people are required for this
installation. Failure to use safety gear and/or attempting
this installation alone can result in property damage,
serious injury, or death.
(G) M6x12 Bolt (x4)
Maximum Load Capacity – 88 lb (39.9 kg)
4. Remove the wall plate and drill a 1/4“ (6 mm) pilot hole
3
4
(H) M6x35 Bolt (x4)
at each location using an electric drill.
(I) M6 Lock Washer (x4)
5. With the help of another person, replace the wall
plate and level it using the bubble guide. Fix it to the
wall using the Lag Bolts (Q) and Lag Bolt Washers (R)
provided (Fig. 1).
4. Follow all instructions and recommendations regarding
adequate ventilation and suitable locations for mounting
your display in the owner‘s manual for your display.
Carefully hook the
display onto the wall plate.
1. Examine the back of your television. If the back of your
display is flat, you will be using one of the shorter bolts
from the hardware kit. If the back of your display is
curved or recessed, you will be using one of the longer
bolts and a spacer (Fig. 4).
(J) M8x16 Bolt (x4)
Be sure you have purchased the correct wall mount
for your TV. Recheck the size and weight constraints.
2. Move the safety tab located on each arm into position
to avoid having the display accidentally lifted from the
mount. A padlock can be inserted into one of the tabs
to help prevent theft of your display (Fig. 6).
(K) M8x40 Bolt (x4)
5. Gather all necessary tools before you begin installation.
You will need a #3 bit Phillips screwdriver, electric
drill, drill bit (included), level (integrated level on
product), stud finder, and hammer (for brick and
concrete installations).
For displays with flat
backs...
For displays with curved
or recessed backs...
(L) M8 Lock Washer (x4)
Fig. 6
A small padlock
can be used to help
prevent theft of
your display
(padlock not
included).
MAF70BK
(M) Small Spacer (x4)
6. It is essential for the wall mount plate to be attached
to wall studs. (Use a stud finder.)
Thank you for choosing the RCA MAF70BK Universal
Flat Panel TV Wall Mount. This mount can be used for all
major brands of 23" - 37" flat panel TVs, 88 lbs (39.9 kg) or
under. This wall mount features a 0-15-degree tilt for easy
viewing. Before attempting to mount your television set,
please remove all parts from this package and read the
installation instructions carefully.
5
6
(N) Large Spacer (x4)
(O) M6 Washer (x4)
7. Use the included hardware for mounting purposes.
This hardware has been provided to ensure a safe and
secure mount.
Fig. 1
8. Hire a licensed electrician to relocate an electrical
Attach the wall plate to the wall.
outlet, if needed.
(P) Concrete Anchor (x6)
(Q) M8x63 Hex Bolt (x6)
9. Be sure to purchase wires long enough to connect
the TV to the audio and video components in your
installation.
WARNING: Use of this mount with a TV weighing
over 88 lbs. or with a screen larger than 37" could cause
the mount to fail causing property damage and/or
personal injury.
6. Do not over-tighten the bolts and do not release the
3. The cable manager can be used to keep your power
wall plate until all screws are secure.
cord and other A/V cables in order.
10.We recommend you hire a professional installer,
if you have any concerns about installing the TV
wall mount yourself.
7. Attach the cable manager to the middle of the top
4. To adjust the tilt position, have one person hold the
display in position while another person loosens the
two tilt adjustment knobs located on either side of
the wall plate (Fig. 7). Once the knobs are loose, move
the display to the desired angle. Re-tighten the knobs
before releasing the display.
(R) Hex Bolt Washer (x6)
crossbar (Fig. 2).
(S) Drill Bit (1)
7
Fig. 4 - Use a longer bolt and spacer for displays with curved or recessed
backs. Do not use the M6 Washer (O) if you are using the M8 Bolts (J or K).
Fig. 2
Attach the
cable manager
to the top
crossbar.
Limited Lifetime Warranty
Keep your sales receipt to obtain warranty parts and
service and for proof of purchase. Attach it here and record
the model number. This number is located on the product.
Fig. 7
Loosen the
adjustment knobs
to change the tilt
angle. There is one
knob on each side
of the mount.
2. Determine the correct diameter bolt to use by trying
one bolt each from Bags 1 - 4 of the hardware kit. Do
not force any of the bolts – if you feel resistance stop
immediately to avoid damaging your display.
Audiovox Electronics Corporation (the “Company”) warrants to you the
original retail purchaser of this product that should it, under normal use
and conditions, be proven defective in material or workmanship during
its lifetime while you own it, such defect(s) will be repaired or replaced (at
the Company’s option) without charge for parts and repair labor.
Model No. __________________________________________
Purchase Date: ______________________________________
Dealer/Address/Phone ________________________________
To obtain repair or replacement within the terms of this Warranty, the
product is to be delivered with proof of warranty coverage (e.g. dated bill
of sale), specification of defect(s), transportation prepaid, to the Company
at the address shown below. Do not return this product to the Retailer.
3. Attach the arms to the back of your display
using the bolts identified in Steps 1 and 2 and the
corresponding Lock Washer (C, F, I, or L) (Fig. 4). You
will need to use the M6 Washers (O) if you are using
the M4, M5, or M6 bolts. If your display has a curved or
recessed back, you may also need to use a Spacer (M or
N).
This Warranty does not cover product purchased, serviced or used
outside the United States or Canada.
This Warranty is not transferable and does not extend to costs incurred for
installation, removal or reinstallation of the product. This Warranty does
not apply if in the Company’s opinion, the product has been damaged
through alteration, improper installation, mishandling, misuse, neglect,
or accident.
Product diagram
Preparing to install
4. Make sure the screws are snug, but do not over-tighten.
THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS
WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S
LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT.
Before beginning the installation process, verify that you
have all the necessary tools on hand. The following tools
are required for proper installation:
Adjustment Knobs
Concrete/Brick Installation
1. Place the wall plate against the wall and level it using
Integrated Bubble Level
the bubble guide.
Specifications
This Warranty is in lieu of all other express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
SHALLBELIMITEDTODURATIONOFTHISWARRANTY.INNOCASE
SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTALDAMAGESWHATSOEVER.Nopersonorrepresentativeis
authorized to assume for the Company any liability other than expressed
herein in connection with the sale of this product.
Tools
2. With the help of another person, mark off six (6)
locations for fixing the mount to the wall.
#3 bit Phillips screwdriver
Stud finder
Model:
MAF70BK
Two-piece, low-profile design
3. Place the wall plate aside and drill a hole at each
location using a 5/16” (8 mm) masonry bit. Remove any
excess dust from the holes.
Description:
RCA Universal Flat Panel TV
Electric drill
Wall Mount
Drill bit (included)
Some states/provinces do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential
damage so the above limitations or exclusions may not apply to you. This
Warranty gives you specific legal rights and you may also have other
rights which vary from state/province to state/province.
TV Size Range:
Maximum Load:
Minimum Profile:
Tilt:
23" – 37"
4. Insert one Concrete Anchor (P) into each hole. A
hammer can be used to lightly tap the anchors into
place if necessary.
5/16" (8mm) masonry drill bit for concrete/
brick installation
88 lbs. (39.9 kg)
3.1" (7.9 cm)
+/- 0-15°
Level (integrated level on product)
Hammer (for concrete installations)
U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd.,
Hauppauge, New York 11788
5. With the help of another person, replace the wall
plate and level it using the bubble guide. Fix it to the
wall using the Lag Bolts (Q) and Lag Bolt Washers (R)
provided (Fig. 1).
Universal VESA Compatibility
Integrated Bubble Level
Cord Management
CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road,
Unit 3, Door 16, Mississauga, Ontario L5T 3A5
Trademark(s) Registered, Marques Deposee, Marcas Registradas.
All other brands and product names are trademarks or registered
trademarks of their respective owners.
6. Do not over-tighten the screws and do not release the
wall plate until all screws are secure.
Padlock Hole
(padlock not
included)
TV Mount Plate
© 2008 Audiovox Accessories Corporation
111 Congressional Blvd., Suite 350
Carmel, IN 46032
7. Attach the cable manager to the middle of the top
Wall Mount Plate
crossbar (Fig. 2).
Security Lock Position
MAF70BK_US_IB_00
|