RLC2626
Important Safety Instructions and Maintenance
Important Safety Instructions
To avoid the fire, no naked flame source,
such as lighted candles, should be
placed on the apparatus.
An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact
with them might be fatal.
Always turn the set off when it is not being used.
Unplug the apparatus from the AC outlet when it will
not be used for a long period of time. And when there
is a lightning, unplug the unit from the AC outlet
immediately. Never touch the antenna wire during
lightning.
Do not pull the plug out by the wire;
Never touch the plug with wet hands.
Excessive sound pressure from earphones and
headphones can cause hearing loss.
Installation
The ventilation should not be impeded by covering the
ventilation opening with items, such as newspapers,
tablecloths, curtains, etc.
At least 10 cm space should be left around the
apparatus for sufficient ventilation.
The product should be situated away from heat
sources such as radiators,heat registers, stoves, or
other products (including amplifiers) that produce heat.
Place the apparatus in such a position that the screen
is not exposed to direct sunlight. It is best to have soft
indirect lighting while watching and avoid complete
dark environment and reflection from the screen as
these may cause eye fatigue.
Keep the product away from high magnetic field (i.e.
power-amplified power speaker) to avoid affecting the
tint;
2
Important Safety Instructions and Maintenance
Installation
Do not place the set on an unstable cart, stand, table
or shelf. The set may fall, causing serious personal
injury as well as damage to the product. Use only with
the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. An
appliance and cart combination should be moved with
care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.
Do not place this apparatus near water, for example,
near a bath tub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or a swimming pool; and
the like;
When the TV being moved in from cold place, it needs
some right time for dew inside unit evaporating fully
before turn on the unit;
Move
To prevent injury, this apparatus must be securely
attached to the floor/wall in accordance with the
installation instructions.
Cleaning
Unplug this apparatus from the AC outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning;
For your protection, please read this instruction completely, and keep this manual for
future reference.
3
Contents
General description
Specifications and accessories
Overview
5
6
7
Basic operation
External connection
Basic operation
Trouble shooting
Picture defects and countermeasures
10
12
14
23
24
Basic operation
4
General description
Feature:
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Zero X radiation complies to green environment protection requirement
Auto tuning and fine tuning
One composite video input socket (back)
One side composite video input socket
One S-Video input socket
One PC VGA input socket
One YPbPr input socket
One HDMI input socket (HDMI 1.3)
One AV output socket
Headphone
Multi-language OSD
Programmable TV sleep timer
No-signal automatic power off function
PC VGA mode: VGA, SVGA, XGA
YPbPr mode:480i, 480P, 576P, 720P, 1080i, 1080P
HDMI mode:480P, 576P, 720P, 1080i, 1080P
Note:
1. In case of any design change,a notice will not be released.
2. The composite video output function only support TV and AV input.
Specification
5
Specifications and accessories
Specifications:
Description
RLC2626
1366X768
~120V 60Hz
4WX2
74W
645X235X493mm
645X108X434mm
TV with stand
Dimensions
(LXWXH)
TV without stand
7.2 Kg
TV with stand
6.4 Kg
TV without stand
Accessories:
l User’s manual l Remote control
l Wall-mounted accessories: Two wall-mounted brackets, four fixed screws
and four fixed sleeves.(Optional)
Note:
1.Due to TV may be used with different display screen, weight marked in this
user's manual or in packaging box are subject to change without notice.
2.The illustrations and on-screen displays in this user’s manual are for
explanation purposes and may vary slightly from actual operations.In case of
any design change, a notice will not be released.
6
Overview
1. Power indicator
Green: Normal playing status.
Red: Standby status.
2. IR remote sensor
Point remote control at this sensor to
conduct remote control.
3. VOL
/
Press these two buttons to increase or
decrease the volume or operate menu.
2
、IR remote sensor
、
1
Power indicator
4. PROG
/
Press these two buttons to select channel
or operate menu.
7
、
5
、
5. MENU
4
、
Press this button to display OSD menu.
6.
3
、
Press this button to enter standby mode
under normal play, and press this button
to enter normal play mode under standby
mode.
6
、
7. INPUT
Press this button to display the selectable
signal source for main source.
8
、
AUDIO(R&L)
VIDEO 2
AV2 IN
10
Headphone
7
Overview
IN
YPb/CbPr/Cr
Connect to YPbPr/YCbCr video.
AV AUDIO OUT
Audio out for external devices.
AV VIDEO OUT
Video out for external devices.
8
Overview
Remote control
Loading batteries:
1) Remove the lid of the battery compartment.
2) Insert 2 size AAA batteries with polarities as indicated inside the compartment.
3) Replace the lid.
Note:
1) One loading of batteries will last 1 year under normal use.
2) If you don’t intend to use the remote control for a long period of time, remove
them to avoid damage due to leakage.
3) Do not mix old and new batteries, or different types.
4) Don’t throw the batteries into fire or water.
5) The batteries (battery pack or batteries installed) shall not be exposed to exces-
sive heat such as sunshine, fire or the like.
9
Basic operation
Remote control introduction
1.INPUT
Select input source.
2.POWER
Turn your TV on and off.
3.0~9
Use these keys to input digit, letters and special characters.
4.INFO
Displays the program information.
5.RECALL
To swap to the previous program you wanted from current program.
6.SOUND
Select audio mode. Press the key repeatedly to choose one of the modes among
Normal, News, Music, Preference.
7.PICTURE
Select picture mode. Press the key repeatedly to choose one of the modes among
Normal, Sports, Mild, Preference.
8.SLEEP
TV will be switched off automatically at preset sleep time if you have set sleep
timer. Use your remote control to set the sleep timer. Press SLEEP button on the
remote control, then press this button again to set sleep timer: Off,15Min,30Min,
45Min,60Min,90Min,120Min.
Note: The sleep timer you have set will be canceled when the TV turns off or if a
power failure occurs.When SLEEP TIMER is 60 seconds only, left tunime will be
displayed on the screen, and any operation will cancel SLEEP TIMER function by
pressing any button on the remote control or on the unit.
9.ZOOM
Change the display mode press the key repeatedly to choose one of the modes
among Full, 4:3.
10.CCD
Select closed caption mode. Press the key repeatedly to choose one of the modes
among Off, CC1, CC2, CC3, CC4, Text1, Text2, Text3, Text4.
11.MTS
Select MTS sound system. Press the key repeatedly to choose one of the modes
among Mono, Stereo, Sap.
10
Basic operation (to be continued)
12.FREEZE
No available for this model.
13.AV
Swith to AV mode directly.
14.YPbPr
Switch to YPbPr mode directly.
15.PC
Switch to PC mode directly.
16.TV
Switch to TV mode directly.
17.HDMI
Switch to HDMI mode directly.
18.
Press this button to shut off sound of the TV temporarily, press again to restore
TV sound.
19.VOLq/p
Press these buttons to adjust TV volume.
20.PROGq/p
Press these buttons to change program upward or downward.
21.MENU
Display the main menu.
22.EXIT
Exit the menu.
23.Arrow buttons(q/p/t/u)
Press these buttons to move cursor up/down/left/right for menu.
24.OK
Validation key.
11
External connection
Antenna connection
Antenna input impedance of this unit is 75ohm. VHF/UHF 75ohm coaxial cable can
be connected to the antenna jack directly, if the antenna cable is a 300ohm flat
feeder cable, you need to use the 300ohm/75ohm converter to connect the antenna
cable to the antenna jack.
l75Ωcoaxial cable is recommended to eliminate interference and double image
due to the unmatched input impedance of the antenna.
lThe antenna cable and power line should not be bundled together.
Stand and Wall-mounted
1. How to mount the LCD TV ?
(1) Take out the bracket hole cover from groove with screw driver and place on the
bracket hole;
(2) Fasten 4 screws into four nuts on the rear cover;
(3) Fasten 2 brackets with 4 M8 screws on the wall as figure 2 shown;
(4) Carefully check for the strength before releasing the LCD TV.
200m m
Nut hole
Figure 1
Figure 2
12
External connection
2. How to assemble the stand?
Before attaching/detaching the stand, make sure to turn off the TV.
Before performing work spread cushioning over the base area to lay the LCD TV on.
This will prevent it from being damaged.
A. M4X8 screw
B. Transition Board
C. M4X8 screw
D. Stand
Figure2
Figure1
Figure3
Assembling instruction:
1.Unfasten screws A from the LCD TV. (Figure1)
2.Detach theTransition Board B from the LCD TV.(Figure1)
3.Fix the stand and the Transition Board together with screws C. (Figure2)
The fixing direction follows the label of the stand and the transition board.
4.Put the transition board and the stand back into the LCD TV. (Figure 3)
5. Fasten screws into the holes to fix the stand and TV cabinet together. (Figure3)
Note: To disconnect the stand from the TV, perform the above steps in reverse order.
13
Basic operation (to be continued)
Turning the TV On and Off
1. Insert the power cord plug into a AC outlet, the TV
will enter standby mode.Press POWER button
on the remote control to turn it on . The indicator
will switch from red to green.
2. If you want to stop watching TV or go out for a
while, you can press POWER button on the re-
mote control. If you want to watch TV again, you
can press this button again.
3. Unplug the power cord when the TV will not be
used for a long period time.
Auto power-off
The TV will enter standby mode in 15 seconds
in PC mode,and in other modes it will enter
standby mode in 5 minutes when no signal
sleep is on.
Memorizing the Channels
Your TV can memorize all of the available
channels. After the available channels are
memorized, use PROGr/sbutton to browse
channels.
Language select
Before using TV, you can set the language:
1) Press MENU button on the remote control, then
press t/u Arrow button to select “Setting” menu
as following:
PICTURE
AUDIO
SETTING
FUNCTION
CHANNEL
LANGUAGE
ENGLISH
SCREEN SAVER
OFF
MID
OSD POSITION
DURATION
ALWAYS
MENU
EXIT
ADJUST
SELECT
14
Basic operation (to be continued)
2) Press p/qArrow button to enter the submenu and press t/u Arrow button to
select the language you desire.
Selecting input source
Press INPUT button on the remote control, then you can select input sources as
following:
TV AV1 AV2 S-VIDEO COMPONENT HDMI PC
Setting color system
In order to meet the color system in your country, you can set the color system as
following: Press q/p Arrow button to select “COLOR SYSTEM” under “CHANNEL”
menu,and then press t/u Arrow button to change video format as following:
AUTO PAL M
PAL N
NTSC M
Tuner setup
Press MENU button on the remote control, then press t/u Arrow button to select
“CHANNEL”:
PICTURE
AUDIO
SETTING
FUNCTION
CHANNEL
SOURCE
AIR
2
CHANNEL
COLOR SYSTEM
SKIP
AUTO
OFF
AFT
OFF
FINE TUNE
55.25MHZ
AUTO SEARCH
ADJUST
MENU
SELECT
EXIT
1) SOURCE
Press q/p Arrow button to select “SOURCE”, and press t/u Arrow button to
select “Air” or “cable”.
2) CHANNEL
Press q/p Arrow button to select “ CHANNEL” and press t/u Arrow button to
select the channel number.
3) COLOR SYSTEM
Press q/p Arrow button to select “ COLOR SYSTEM” and press t/u Arrow
button to select the right color system.
15
Basic operation (to be continued)
4) SKIP
Press q/p Arrow button to select “SKIP”, then press t/u Arrow button to select
“On” or “Off”. On: skip the channel; Off: not skip.
5) AFT
Press q/p Arrow button to select “AFT”, then press t/u Arrow button to select
“On” or “Off”.
6) FINE TUNE
In case of bad image or sound of TV program, you can use Fine Tune function
to obtain satisfied image or sound with operating steps as follows:
Press q/p Arrow button to select “FINE TUNE” and press t/u Arrow button to
conduct fine tuning from high frequency to low frequency or from low fre-
quency to high frequency till best picture or sound effect is obtained.
Note: Only if “AFT” is set to “OFF”,you can adjust the “FINE TUNE”.
7) AUTO SEARCH
Press q/p Arrow button to select “AUTO SEARCH”, then press u Arrow button
to start Auto Search:
AIR
AUTO SEARCH
CH:
1
TV will tune automatically and all programs found will be saved. Please don’t
interrupt it.
Note:
i) If you use the TV for the first time, you must use “AUTO SEARCH” to search
and memorize all channels.
ii) If your TV is not in TV input state, you must switch it to TV state at first.
iii) If you want to stop the process of “AUTO SEARCH”, just press MENU button
to exit.
16
Basic operation (to be continued)
Adjusting the Picture
Press MENU button on the remote control, then press t/u Arrowbutton to select
“PICTURE” menu.
PICTURE
AUDIO
SETTING
FUNCTION
CHANNEL
PICTURE MODE
BRIGHTNESS
PREFERENCE
50
CONTRAST
COLOR
50
50
TINT
50
50
50
SHARPNESS
BACKLIGHT
COLOUR TEMP.
STANDARD
FULL
SCALE
MENU
EXIT
ADJUST
SELECT
1) Adjusting Picture Mode
Press q/p Arrow button to select “PICTURE MODE” , and press t/u Arrow
button to adjust picture mode to your desire.
Note: “BRIGHTNESS” , “CONTRAST” , “COLOR” adjusting are only available in
preference mode.
2) Adjusting the Brightness of picture
Press q/p Arrow button to select “BRIGHTNESS” , and press t/u Arrow button
to adjust brightness to your desire.
3) Adjusting the Contrast of picture
Press q/p Arrow button to select the “CONTRAST”, then press t/u Arrow
button to set contrast to your desire.
4) Adjusting the Tint of picture
Press q/p Arrow button to select the “TINT”, then press t/u Arrow button to set
tint to your desire.
Note: Only available in NTSC.
5) Adjusting the Color of picture
Press q/p Arrow button to select the “COLOR”, then press t/u Arrow button to
set saturation to your desire.
6) Adjusting the Sharpness of picture
Press q/p Arrow button to select the “SHARPNESS”, then press t/u Arrow
button to set sharpness to your desire.
7) Adjusting the Backlight of picture
Press q/p Arrow button to select the “BACKLIGHT”, then press t/u Arrow
button to set backlight to your desire.
Note:Backlight function is only available for models with this function.
8) Adjusting the Color Temp of picture
Press q/p Arrow button to select the “COLOUR TEMP.”, then press t/u Arrow
button to set colour temperature to your desire.
9) Adjusting the Scale Mode of picture
Press q/p Arrow button to select the “SCALE”, then press t/u Arrow button to
set scale mode to your desire.
17
Basic operation (to be continued)
Note: It is useless under no signal mode.
Adjusting the Sound
Press MENU button on the remote control, then press t/uArrow button to select
“AUDIO ” menu.
PICTURE
AUDIO
SETTING
FUNCTION CHANNEL
SOUND MODE
EQUALIZER
PREFERENCE
50
BALANCE
AVL
OFF
MONO
MTS
MENU
EXIT
ADJUST
SELECT
1) Adjusting Sound Mode
Press q/p Arrow button to select “SOUND MODE”, use t/u Arrow button to
adjust sound mode.
2) Adjusting the Equalizer
Press q/p Arrow button to select “EQUALIZER”, use t/u Arrow button to adjust
the frequency.
3) Adjusting Balance of sound
Press q/p Arrow button to select “BALANCE”, use t/u Arrow button to adjust
sound balance.
4) Adjusting AVL
Press q/p Arrow button to select “AVL” and press t/u Arrow button to set it
“ON” or “OFF”.
5) Adjust MTS
Press q/p Arrow button to select “MTS”, use t/u Arrow button to adjust to your
desired.
Note: Only available in TV.
OSD Setup
Press MENU button on the remote control and press t/u Arrow buttonto select
“SETTING” menu.
PICTURE
AUDIO
SETTING
FUNCTION CHANNEL
LANGUAGE
ENGLISH
SCREEN SAVER
OFF
MID
OSD POSITION
DURATION
ALWAYS
MENU
EXIT
ADJUST
SELECT
18
Basic operation (to be continued)
1) OSD Language
Press q/p Arrow button to select “LANGUAGE” and press t/u Arrow button to
select language you desire.
2) Adjusting SCREEN SAVER
Press q/p Arrow button to select “SCREEN SAVER” and press t/u Arrow
button to set screen saver.
3) Adjusting OSD Position
Press q/p Arrow button to select “OSD Position” and press t/u Arrow button
to set position of OSD.
4) Adjusting OSD Timer
Press q/p Arrow button to select “DURATION”, Press t/u Arrow button to
select one time from the following times:5s,10s,15s and always.
Function setup
Press MENU button on the remote control or TV side panel, press t/u Arrow button
to select “FUNCTION” menu.
PICTURE
AUDIO
SETTING
FUNCTION
CHANNEL
SLEEP TIMER
OFF
NO SIGNAL SLEEP
OPC
ON
ON
CLOSED CAPTION
PARENT CONTROL
OFF
MENU
EXIT
ADJUST
SELECT
1) SLEEP TIMER
Please refer to page 10.
2) NO SIGNAL SLEEP
Refer to page 14 “Auto power-off”.
3) OPC
Press q/p Arrow button to select “OPC” in “Function” menu. press t/u Arrow
button to set it “ON” or “OFF” or “DEMO”.
Note: Not available in VGA.
4) CLOSED CAPTION
Press q/p Arrow button to select “CLOSED CAPTION” in “Function” menu.
Press the key repeatedly to choose one of the modes among Off, CC1, CC2,
CC3, CC4, Text1, Text2, Text3, Text4.
19
Basic operation (to be continued)
5) Parent Control
In “Function” menu, press q/p Arrow button to select “Parent Control”,press t/
u Arrow to enter the input password menu. Input the password to enter the
submenu(the default password is 0000 and omnipotent password is 1980).
PICTURE
AUDIO
SETTING
FUNCTION CHANNEL
CHANGE PASSWORD
CHANNEL LOCK
VIDEO LOCK
OFF
MENU
EXIT
ADJUST
SELECT
(1) Change Password
1.Press q/p Arrow button to select "CHANGE PASSWORD" option.
2.Press t/u Arrow button and input a new password twice to change the
password.
(2) Channel Lock
1.Press q/pArrow button to select "CHANNEL LOCK" option.
2.Press t/u Arrow button to enter the submenu.
lSource
1.Display the current channel source.
PICTURE
AUDIO
SETTING
FUNCTION CHANNEL
SOURCE
AIR
_
_
_
_
_
_
_
_
_
CHANNEL INPUT
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
CLEAR ALL
MENU
ADJUST
SELECT
EXIT
20
Basic operation (to be continued)
lChannel Input
1.Press q/pArrow button to select "CHANNEL INPUT" function.
2.Input the channel number you want to lock and press OK key to confirm,the
channel number will be add to the list below.
3.If you want to unlock a channel, press q/pArrow button to select the channel
number in the list and press OK key to delete it.
Note: You can lock 9 channels in "AIR" or "CABLE" source.
lClear All
1.Select a source you want to clear in "SOURCE" function.
2.Press q/p Arrow button to select "CLEAR ALL" function.
3.Press t/u Arrow button to clear the channel list in the source you select.
(3) Video Lock
1.Press q/pArrow button to select "VIDEO LOCK" option.
2.Press t/uArrow button to select "VIDEO" , "VIDEO+" or "OFF".
lVideo: Lock all sources except TV.
lVideo+: Lock Channel 3 and channel 4 of TV and all other sources.
lOff: Close "VIDEO LOCK" function and all sources are available.
Note: If the sources have locked, the key in Remote is not available in AV, TV,
COMPONENT, PC,HDMI input.
PC Adjust
1.Picture
When the TV is in PC mode, press MENU button on the remote control panel.
Presst/u Arrow button to select “PICTURE”.
The method to adjust Brightness, contrast, Backlight, color Temp, and scale, please
refer to “Adjusting the Picture”.
PICTURE
AUDIO
SETTING
FUNCTION
WINDOW
PICTURE MODE
BRIGHTNESS
CONTRAST
PREFERENCE
50
50
BACKLIGHT
50
COLOUR TEMP.
WARM
FULL
SCALE
MENU
ADJUST
SELECT
EXIT
21
Basic operation (to be continued)
2.Window
This TV supports no higher than 60Hz under PC mode, so please set the refresh
rate of PC to 60Hz. If the frequency is higher than 60Hz, the screen may flicker.
When the TV is in PC mode, press MENU button on the remote control. Press t/u
Arrow button to select “WINDOW”.
PICTURE
AUDIO
SETTING
FUNCTION
WINDOW
PICTURE
AUDIO
SETTING
FUNCTION
WINDOW
H-POSITION
V-POSITION
100
100
H-POSITION
V-POSITION
100
100
CLOCK
PHASE
100
0
AUTO ADJUST
MENU
MENU
ADJUST
SELECT
EXIT
ADJUST
SELECT
EXIT
1) Adjusting picture H-Position
Press q/p Arrow button to select “H-POSITION” and press t/u Arrow button to
set horizontal position of picture.
2) Adjusting picture V-Position
Press q/p Arrow button to select “V-POSITION” and press t/u Arrow button to
set vertical position of picture.
3) Adjusting Clock
When PC is connected to TV set because of the difference of PC parameter,you
should adjust the “CLOCK” item in “WINDOW” menu until you get a good picture.
4) Adjusting Phase
When PC is connected to TV set because of the difference of PC parameter,you
should adjust the “PHASE” item in “WINDOW” menu until you get a good picture.
5) Auto Adjust
If there are unexpected problems happened when you adjust the items, you can
select the “AUTO ADJUST” and press u Arrow button, the TV set will resume the
original settings.
Note: Only “H-Position” and “V-Position” are available for YPBPR mode.
22
Trouble shooting
If you have any problem, check the countermeasure for each symptom listed below.
The following symptoms may have caused by inappropriate adjustment rather than
actual malfunction of the unit. If the trouble persists, contact the service center.
Problem
Possible Solution
Try another channel.
Poor picture and sound quality
Adjust the antenna.
Check all wire connections.
Try another channel.
Press the TV/AV button.
Make sure the TV is plugged in.
Check the antenna connections.
No picture or sound under TV status
First, check the volume of units connected to your TV.
Adjust the TV volume accordingly.
Check sound adjustment(Volume and Mute)
No sound or sound is too low at
maximum volume
Make sure the program is broadcast in color. Select the
picture menu, then adjust the color or tint submenu to the
proper value.
No color, wrong colors or tints.
Picture rolls vertically.
Check all wire connections.
Blurred or snowy picture, distorted
sound
Check the direction, location and connections of your antenna.
This interference is often due to the use of an indoor antenna.
Replace the remote control batteries.
Check the battery terminals.
Remote control malfunctions
Remote is out of range, move close to TV
Confirm there is no obstructions between remote and TV
Make sure power cord is plugged in
Image is not centered on the screen.
Adjust the horizontal and vertical position
When cleaning the LCD screen, please pull out the power
plug, use dry and soft and clean cloth to clean the dust on the
screen and shell. In case of further cleaning for the screen,
please use clean wet cloth. Do not use naphtha, thinner or
similar liquids for cleaning.
Clean TV set
This product adopts a high-resolution LCD TV, and the colored
point of some pixels may occur due to the special feature of
the product. For a few of colored points, this shall not be
related with terrible product performance or product reliability,
and in case of this situation, the service of the product will not
be influenced. For the criterion of colored points, our company
has similar products with others. The colored point in
conformity with the product criterion is not covered by the
return scope of the product due to quality problems. We hope
our respected customers will forgive us.
Colored point
23
Picture defects and countermeasures
The most common types of television interference are
as following:
SNOWY PICTURE
Snowy picture is usually caused due to weak signal.
Adjust antenna or install an antenna amplifier.
DOUBLE IMAGES OR “GHOSTS”
Double images are usually caused by reflections from
tall buildings. Adjust the direction of the antenna or
raise it.
RADIO WAVE INTERFERENCE
Wave pattern are moving on the screen, which are
usually caused by nearby radio transmitter or shot-
wave receiving equipment.
HIGH TEMPERATURE ELECTROTHERMAL INTER-
FERENCE
Diagonal, or herring-bone, patterns appear on the
screen or part of picture is missing. This is probably
caused by high temperature electrothermal equipment
in the nearby hospital.
24
RLC2626
|