OPERATING PROCEDURES
VOLTAGE SELECTOR
Use this switch to select the
proper Voltage for your region
VOLTAGE ELECTOR
110~ 120V
60Hz
220~ 230V
50Hz
DC
RISK OF ELECTRIC SHOCK
DO NOT OPEN
LIN E
(IN)REC
PLAY(O UT)
CASSETTE DECK
INTEGRATED CIRCUIT
REMOTE S YS TEM
TO AMP
VO LTAG
E
S
E
L
E
C
T
O
R
V
R
E
M
O
T
E
S
YS TE
M
E Q
TAP
E
T UNER
C
D
PA
1
1
0
6
~
0
1
2
z
0
V
2
2
0
~
2
3
0
H
5
0
H
z
R
IG
H
T
L
E
FT
INTE G
AC 22 0
R
V
ATE D
C
IR
~
C
50 Hz
UIT
TAP
LAY
E
E Q
-
23 0 V
T UNER
C
D
AV1
AV2
AUX
P
R
EC
P
LAY
R
EC
L
R
_
_
AU
D
IO
Playback a recorded tape ( DECK A or DECK B)
1. Switch on the power of the unit.
2. When Cr02 tape is used for recording, press the REC
Cr02 switch.
2. Press the STOP/EJECT button and insert a recorded
cassette. For Cr02/metal tape, further press the
Cr02/metal switch and the light at the indicator will be
lit up.
3. Press the record button. The level meter at the peak
level indicator will shift and the REC light will be lit
up indicating that recording is underway.
4. Press the STOP/EJECT button to stop recording at any
time.
3. Press the PLAY button.
4. Adjust the AMPLIFIER VOLUME and GRAPHIC
EQUALIZER controls for your desired sound level
and taste.
5. Press the STOP/EJECT button to stop playback at any
time.
Pause
Press this button to momentarily stop tape travel during
recording. Re-press this button for pause release and
recording restart.
Dubbing operation (DECK A→ DECK B)
This unit enables you to dub a recorded tape to another
tape by using the built-in double deck mechanisms. It is
performed only one way from DECK A to DECK B.
Preparation
1. Insert a cassette for playback in DECK A.
2. Select tape DIRECTION button (FFWD or REW ) for
the desired location of the tape to the beginning.
3. Insert a cassette into DECK B.
4. Select the dubbing speed by the dubbing High speed
switch.
5. There are two dubbing speeds: high speed and normal
speed.
6. For high speed dubbing, press the High speed switch.
The light at the indicator will be lit up and high speed
dubbing is then activated.
7. Normal speed dubbing requires no pressing of the
High Speed Switch. No light will be shown at the
indicator at all.
8. Press the PAUSE button of DECK A.
9. Then press the PLAY button of DECK A.
10. Press the RECORD button of DECK B.
11. Press the PAUSE again of DECK A to release the
pause mode. The unit will start the synchronized
dubbing operation.
Fast forward and rewind (DECK A or DECK B)
For fast winding or rewinding the tape, press the FFWD or
REW button. Press the STOP/EJECT button when the
desired location has been reached. When the end of the
tape has been reached, the FFWD or REW button will be
released automatically.
Pause (DECK A or DECK B)
Press the PAUSE button to momentarily stop tape travel
during playback or recording. Re-press the button for
pause release and playback or recording to re-start.
Full automatic stop (DECK A or DECK B)
Press the STOP/EJECT button to stop playback or
recording at any time. When the end of the tape has been
reached, any of the PLAY, REC, REW or FFWD buttons, if
pressed, will be automatically released and the head block
completely separates from the tape and capstan. This
protects tape and prevents pinch roller wearing out.
RECORDING (DECK B)
When recording, use the DECK B.
Manually level control recording (for external source)
This unit has record level volume to adjust the record level.
Usually, the volume has a center click. When it reached the
center click position, the tapes can be recorded normally. If
the sound source signal is too strong, a red spot will be
appeared in the record level indicator. You can adjust the
record level volume to the left position and vice versa.
In normal state, the sound source level is between the red
and green spots ( that’s 0dB).
12. To stop dubbing operation, press the STOP/EJECT
button of DECK B.
Note: Do not change dubbing speed during dubbing
operation.
1. Press the TOP/EJECT BUTTON and insert a cassette.
- 2 -
SPECIFICATIONS
Type……………………………Stereo double cassette deck Motor………………………DC servo motor x 2
Track system…………………. 4-track 2- channel
Tape speed……………………..4.8 cm/sec
Frequency response
Fast Forward/Rewind time..Approx.100 sec
with C-60 cassette
Input terminals
(-20dB recording)
LINE IN X 2………………Min. input level:600mV(0dB)
Input impedance: 50 kΩ
Chrome tape………………….40-15,000Hz (±3dB)
Normal tape………………….40-14,000Hz (±3dB)
(0 dB recording)
Output terminals
LINE OUT X 2…………….output level: 600mV (0dB)
output impedance: 5 kΩ
Chrome tape…………………40-8,000Hz (±3dB)
Normal tape……………. …..40-8,000Hz (±3dB)
S/N ratio……………………….58dB
Power requirement………...AC220V, 50Hz
power voltage………..230V, 50Hz
For U.K………………240V, 50Hz
For U.S.A. & Canada…110V, 60Hz
Power consumption……watts VA Rated
watts Maximum
Wow and flutter………………..<0.2% (DIN45500)
Crosstalk……………………….40dB (1 khz)
Harmonic distortion………….less than 1%
(at 1 Khz, OVU 3rd
H.D. Normal tape)
Dimensions………………...360mm x 128m x246mm
(W x H x D)
Channel separation…………. .40dB (1 khz)
Head……………………………Deck A
For Playback
Weight………………………4Kg (8.5 Ibs)
ACCESSORIES……..Pin plug cord…2
Deck B
For recording/playback,
2-gap ferrite head for
erasure
Design and specifications are subject to change without notice.
- 3 -
|